Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hi team ,
I'm using sdk 12.1.0(E:\testing\examples\ble_central\ble_app_hrs_c\pca10028\s130) example.I want to change to this BLE_GAP_ADV_TYPE_ADV_NONCONN_IND in above example...
I'm using nRF52 + SDK11.0.0 + s132. I have a custom service (with a read characteristic and a separate notify characteristic). After adding the DFU service and uploading the...
Hi,
Following the docs I think I am able to write to flash but it will not read anything .
This is how I set it up, write and read :
static void sys_evt_dispatch(uint32_t...
Hi,
I used a PCA10040 dev kit with nrf52832 to test Serial Secure DFU Bootloader.
Followed all the steps in the example with my PC (Ubuntu 16.04.1 LTS 64-bit).
I...
I am using SDK 12.2.0 with soft device s132 3.0.0 using NRF52 Development Board(PCA10040).
I want to update Battery level to central device/APP.As i want to use code for...
Hi,
I am working with a nRF51822 chip placed on a Ble Nano v1.5 board and I would like the schematic of Ble Nano v1.5. Could anyone tell me where I can find the schematic...
Hello,
I am using pca10028 and sdk12.2. I am trying to take sensor reading via TWI and I want to send this reading over ble. So I am trying to add twi files in ble_app_template...
I am attempting to increase the queue size for handle value notifications to support a higher number of packets per connection event. However, I am unable to set the queue...
Hello,
I'm working on nRF52832-DK with SDK11 on linux.
Is there an example to use whitelisting ? I'm trying to use HIDS_Mouse but it's not working.
How can I write...
i have learn how to program nRF51 DK with and without softdevice. Now i want design code as per my requirement... but find difficulty to understand given sequence of code...
Hi,
I am working over nrf51822 ble and I have some security issues with that. I'm programming an android app to connect to the nRF51822 (peripheral). Without any security...
Hi.
I'm trying to control a keyboard and a mouse with nRF24LU1+ USB dongle module.
www.nordicsemi.com/.../nRF24LU1P
I downloaded this link below from the Nordic website...
1\select zip file
2\scan and select nrf51 dev
3\upload.
then the nrf51 enter dfu mode, and can scan the dfutag ble dev. but the ADDR auto add 1 . Wait about 10 seconds...
Hello everyone.
I've got the nRF51822 Evaluation Kit and Dongle. The heartbeat demo is working, so I got the toolchain -- Nordic, Keil, Segger under Win7 -- set up correctly...
Hie,
Is it compulsary for us to send only 20 bytes of data or less than that in one packet in BT5 as we used to do it in BT4 to make BT5 compatible in communicating with...
