HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I am upgrading to SDK 11.0.0 and S130 v2.0.0 from SDK 9.0.0 and S130 1.0.0 and I am stuck with an error when I call sd_ble_gap_adv_start. Here's the code that now fails...
I have the following two lines with pin 21 not connected to anything:
nrf_gpio_cfg_input(21, NRF_GPIO_PIN_PULLUP);
uint32_t value = nrf_gpio_pin_read(21);
I would...
Hello!
I'm trying to flash my SeeedStudio Tiny BLE board (nRF51822 QFAA) with SoftDevice S110 using Keil but it doesn't look like it's going to let me. I'm just getting...
Hi,
i am having some trouble getting my nRF52 DK (S132) to read a value provided by the nRF51 dongle(S130).
First of all, i am very new to this whole Bluetooth thing so...
Hello!
I'm trying to read 16 bit ADC Value on nRF Master app instead of only 8 bit, and I know that there is the example code on github which is only send me the 8 bit...
We have a new daughter board connected via I2C to an Atmel controller. What we need to do is load the right softstack onto the NRF and then send the needed commands to tell...
Hi Guys,
We have schematic of future NRF 51822 project, who can help us with PCB design? Or who can suggest me where i can do it?
PCB.DXF
schematic.pdf
Hello All,
I am trying to build a BLE peripheral project with RTX OS which is using S110 Soft Device and bootloader is also there in Flash memory region. So when I am trying...
I am just beginning to develop with BLE.I came across the nRFgo Studio through Nordic and BDS through the bluetooth SIG.
1]What are similarities/differences between the...
Hi.
I want to active HW timer with SoftDevice 7.1.0 .
Timer operation is good but I can not stop the timer.
The power consumption is 200~300uA after timer expired ( or...
Hi,
We would like to use NRF52832 chipset for our project, and we need to configure 11 pins as GPIO interupt , Is this possible ? How many pins we can have as interrupt...
I have Bluetooth iOS app communication with my nRF51822. I notice that when I connect the the nRF, the first GATT write event is always the same:
p_ble_evt->evt.gatts_evt...
