Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
I'm still having a bit of trouble getting my board to receive Heart Rate information from the demo example provided in the 7.2.0 SDK. I've configured the network key correctly...
I am trying to hook up the following accelerometer with my MPU-3050, but I am having trouble reading from the registers. So far I have code that looks like this.
Accelerometer...
Is it possible on the nRF51822 to surface an every from the Soft Device whenever a client attempt a scan (is it SCAN_REQ?)
This is for an iBeacon implementation where I...
I'm doing some work with the nRF51822 smart beacon kit. I tried to do an over the air firmware update of the application, but kept getting dfu invalid state (2) errors after...
We've got an application (not using SD or SDK functions) that locks up the nRF51822 and does not reset even though the watchdog is configured and confirmed to work in all...
The release notes for SD 8.0 note "The default behavior is now that the application can use the CPU while the radio is active".
Does this mean that this code is no longer...
Hi,
I am trying to connect the demo board nrf6929 to my demo nrf51822 (PCA10001).
In nrfready_voice_input_module_user_guide I couldn't find any information about updating...
Hi,
I'm using a lightly modified copy of the Multilink central S120 example code. When I get to ble_stack_init() the first thing it does is SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
I found the Ble Serialization here and the example sourcecode within the sdk sources.
It uses uart with 38.400 Baud and hardware handshake (Rtc/Cts).
Is there also example...
Hi,
Looking at the manuals for the S110 and S120 soft devices, I don't see mention of the bootloader in the S120 manual. Does S120 support bootloaders?
I want to make...
Reading the following post:
devzone.nordicsemi.com/.../
made me think that I could use either the nRF51822 or nRF8001 in my design. However, the following post:
devzone...
Hello everyone,
I have had an idea for a cheap homemade programmer for nRF51822. I don't know if it could work, it's just an idea I would like to discuss with you.
I...
I am trying to port the SDK 8.0.0 to use the IAR ARM tools and I am having a problem getting the linker to link the file system_nrf51.c that is called from iar_startup_nrf51...
Might I know the spec of the antenna which come with nrf51822-DK?
is it 50Ohm?
I try to use patch antenna on the nrf51822-DK. the perform i measure not very good at all...
