hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi, the provisioning works and after that the dk is capable to get mesh messages but oddly enough a restart brokes this feature.
The error message is:
0x0c means BT_HCI_ERR_CMD_DISALLOWED...
Trying to install nrfutil on a system with Python 3.9 but it only installs the old version 5.2.0 which is broken on Python 3. This is the last version before the version check...
I use the internal LFCLOCK to drive my application. Sometimes, I need a more accurate clock to do time measurement. At startup, I can start the external crystal oscillator...
Hi,
I am trying to get Secure UART Bootloader to work and followed the steps mentioned here .
I generated the Keys and updated the dfu_public_key.c file in the project...
Hello,
I'm planning serial wire flash writing from custom board gpio to nRF52840 serial wire.
nRF52840 SWDIO/SWCLK/NRST are connected to a custom board GPIOs.
Is there...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
We built 2 configurations for...
I’m using nRF52810 in my design and for BLE communication I want to use Data Length Extension (DLE). Currently I’m using SDK v 15.2.0 , S112 and since DLE cannot take place...
Hi,
I have a very strange issue on my nRF5 development kits and dongles. Whenever I load the softdevice and firmware to the DKs or dongles. After sometime, the USB connection...
when I use central and Peripheral all concerned, Eight Peripheral connected to the central 。when I'll connect my phone to the central Peripheral . Device Error
Here's the...
Hello,
I am using a nrf52 DK in an educational context.
For this reason, I am not using the SDK, but implement basic features on a lower level.
I used the implementation...
I would like to confirm that the temperature measurement is sent from the end-device to the coordinator using the example zigbee temperature sensor.
I'm looking at Testing...
With the introduction of mesh_config_file_clear() in 4.2.0 the behaviour of mesh_config_clear() was changed such that only a subset of all the file ids handled by the Mesh...
How to add new i2c based sensor device to ncs\v1.3.0\zephyr\drivers\sensor.
Can you suggest any tutorial to do so as i want to use sensor subsystem which in turn uses i2c...
I have produced ~ 15 different custom board variations that all use the nRF52810-CAAA. They all have the same reference schematic, and use 4 programming pins (V, G, SWDIO...
Hello,
I have an application that uses the SPI- and the TWI-Manager:
But the application throws the error code 17 when the program tries to initialize the TWI-Manager...
