Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
Hello:
We have a BLE project running on the BMD-300 from Rigado for which we want to add BLE DFU functionality. I am basing our development on the "ble_app_buttonless_dfu...
Hello,
I want to measure the current in system off mode.
I am flashing the S110 softdevice and bootloader in the nrf51822 chip.
Using BLE i am flashing an application...
Hi nordic
I'm developing using nrf52832
This board has many example code so I'm developing smoothly
but Today I had problem. It is about check time
I want to check...
Hello, I use light switch example (nrf52832, mesh sdk 2.0.1)
Can I create mesh network without servers? (clients will send messages to each other and process them)
And...
Hi, I want to use 2 I2C instances and 2 SPI instance during setup, and later switch to 1 I2C instance and 3 SPI instance. To do this, I tried to swap TWIM2 instance to SPIM2...
I'm looking to build a product which require an Android board with relay and BLE 5. I am very new to this and so far I have been playing with Raspberry Pi where the BLE and...
Hello, this will be a bit of a long-winded explanation but here goes: I'm building an SPI driver that reads data from an external ADC and writes to a PWM signal. I got the...
I figured that I could put
#define TX_POWER_PHIL +8 /** -40,-20,-16,-12,-8,-4,0,+2,+3,+4,+5,+6,+7,+8 phil **/
and then make two changes to
static void advertising_init...
Is any GPIO, as output, logic level on nRF52832 maintained when the device is in OFF mode? Same question when the system is in ON/Low power mode Thank you
Hi guys!
I am making an application that uses the PCA10056 for 2.4Ghz RF communication using Enhenced shock burst(esb).
Also, when upgrading the application, i try to...
Hi all. I fell into despair in an attempt to find a solution. If I do not use sprintf then everything works fine.
Before calling some_f, mqtt_put works without any grudges...
Function softdevice_enable() doesn't return any adjusted warnings in case of changing central/peripheral connections, e.g. my ble_stack_init() function:
static void ble_stack_init...
Hello, nordic.
I studing nfc example for oob pairing.
So, I have to intergrate to uart example and hrs nfc example.
I had intergrated uart function in hrs_nfc example...
I am trying to decide whether to use free-rtos or bare-metal.
In the documentation for the nRF SDK v15.0.0 i see that free-rtos is not supported for the nRF52840.
However...
