Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
"SES > File > Open nRF Connect SDK Project..." does not seem to include a thread aware script for Zephyr. Is there a provided script for this somewhere? If not is there a...
Hello,
I would like to use a single COMP I/O pin to compare the pin voltage to multiple references during run-time.
To do this, I was planning on initializing the COMP...
With SDK For Mesh v5.0.0 the mesh_stack_power_down() was actually implemented but there is a bug that will disabled the proxy permanently.
For some unknown reason the mesh_stack_power_down...
Trying out the Sensor Model supplied with SDK For Mesh v5.0.0 raise a few concerns.
The way sensor_initialize() is made requires all supported PropertyId helper functions...
Hello For my application (which is based on the ble_thread_dyn_mtd_coap_cli example), I would like to be able to send a file (for an update) using bluetooth. To do this, I...
Hi, I have been studying a lot of issues reported here about leaving network and joining another. The most common answer is to use zb_bdb_reset_via_local_action(0); But when...
Hello,
I am using nRF52833, nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 and SEGGER Embedded Studio for ARM 5.34.
I have imported the ble_zigbee_dynamic_door_lock_nus...
Hello,
I am looking at using the nRF52805 in a new design, but I am worried about the 0201 and 0402 components that are recommended. Currently, my company manufactures our...
Hi,
I am evaluating Zephyr mesh and implemented two timers; one triggers at every 2 mS, the other triggers at every 500 uS.
I put a code in both timers' events to toggle...
Hi, Our platform is NRF-52833 Our project use RS485 bus (nordic's uart + a 485 chip) to communicate with other device. And we choose the libuarte to be the uart handler to...
Hi,
In the nRF_SDK_for_Thread_and_Zigbee_v4.1.0, in examples/thread/NCP/radio folder, there is no option for compiling the firmware for PCA10059.
I want to run RCP firmware...
Hello guys,
I'm trying to interface ds18b20 temperature probe and I'm using this code , In termite its showing output as -0.062500 I don't know why can anyone tell what...
Hello,
I'm using NCS 1.4.99 with a nRF5340DK and want to use the hardware CS of the SPI and also use BLE.
Here is a simple code that work on a nRF5340PDK but only work...
Hi All,
I was just reading the white paper on RF testing guidelines, and I noticed several times there have been mentions of "nRF Performance Instructions" for each of...
