I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
we've got a quite unpredictable issue with a hardfault call : actually this is in this function call : app_error_fault_handler (in app_error_weak.c file)
We use...
I am using the zephyr rtos which run on the nrf52832.
Describe the bug We are using a nrf52832 based board. There are some I2C devices like tsm12 and eeprom. The power consumption...
I'm getting a strange assert from S140 7.2.0 nRF5_SDK_17.0.2_d674dde on a nRF52840 at PC 0x15074.
Frustratingly, it happens a minute or so after boot, but doesn't occur...
Hello Nordic
Im having issues getting logs out of the MSC storage example on SDK16.
When connecting nRF USB connector on the PCA10056 connector to my Windows 10 computer...
Hello,
We use the nRF52832 with SD 17.2.0, Bluetooth LE.
We observe an error when doing the following sequence:
- Build a bonded connection using the nRF Connect...
Hi,
When using the TWI manager you normally provide a callback function that is executed once the transaction has been completed. I'm using the NRF logger module to display...
Hi, Nordicsemi
At present, although SPI uses easy DMA when reading and sending data, in the actual use scenario, I still use gpiote to detect the interrupt pin of the sensor...
I am using the sdk-zephyr. After configing the ubuntu enviroment, i use the west build commond to build the sample project.
But there are errors like these:
[0/1] Re-running...
Hello,
I have few questions about PPI.
----------
1. How to configure PPI channels that runs one after the other? If yes, is there any example?
Because I have two...
I'm having trouble getting the Secure Entry gateway functions to work out of RAM. The nRF9160 datasheet has RAMNSC configurations, so it should be possible. We're able to...
Hello,
I'm not able to locate the QDID for S113 v7.2.0, associated with nRF52832 and SDK 17.0.2.
The product page for S113 indicates that S113 is Bluetooth 5.1 qualified...
Hello,
two part question;
-when a device is registered with the FCC, there is a good amount of documentation uploaded to the FCC website like test reports, photos of the...
Hi I'm wondering if anyone has any tips on implementing a I2C recovery sequence with NRFX 2.3.0 (as included with Zephyr 2.4.99). I've seen this discussed https://devzone...
Based on zigbee sdk 4.1, in the sample code of light_switch, leaving the network and joining the network are completed by buttons, the code is as follows:
Seen from the...
