Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
can ble_flash_page_erase return an error_code if erase uncuccessful? ble_flash.h show that it can ,but the code of ble_flash.c seem that it can not
uint32_t ble_flash_page_erase...
I am working on a project which is currently based on the nRF51922, and I would like to look at the S310 specification document. I found a link on this page: www.nordicsemi...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi,
I'm trying to set up an iOS app (which I know is working properly) with a nRF8001 using nRFGo studio. I do not have the nRFGo dev kit (only the 8001 dev kit) so I hooked...
Hi
How to set device address in nRF8001?
I only see get device address command.
Does it mean I just only put my device address in MCU?
Thanks.
BR
Atlas
Hi,
I'm trying to generate some time variant values for testing purposes... rand() always returns 1447534768! This is in the proximity app FWIW.
So, I thought I would...
nrf24le1 memory map shows that there are two sram block size of 512byte ,the first one is data retentive (address 0-0x0200) ,another one is data non retentive (address 0x0200...
My device use the firmware program ble_app_uart to connect the nexus 7 which Installs the nRF UART 2.0 for Android 4.3 。The first connection is ok，and Data sent and received...
Hello,
I am a beginner in the world of bluetooth and bluetooth smart connections. I am working with an nrf51822 Evaluation kit an android phone (Nexus 4 running 4.4.2)...
Is it normal that after cutting SB8 our chip is still working when connected to USB port? (in case of battery we need to connect pin 1 and 2 from P1). I spend long time looking...
I have a custom board that uses the nrf51822. I have been using the sample application ble_app_uart with only one minor change, I use the internal clock (NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION...
I'm wondering when my firmware changes over time what will happen with information stored with pstorage? For example if I my new firmware release adds an additional pstorage_register...
If I have persistent data that will be updated semi-frequently, will pstorage wear out the flash memory? What steps should I take to be sure my data storage will remain functional...
