I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Just wondering,
What if I configure the Tx power level or some other attribute. What do I have to do to save the value to be used when the unit restarts?
Hello all,
I would like to ask you something,
I've done all my development with NRF24L01+ but now I have some NRF24L01 modules.
I know that NRF24L01+ is fully compatible...
Hi
I am created one more timer in ble_app_hrs
like in timer_init()
err_code = app_timer_create(&m_current_timer_id,
APP_TIMER_MODE_REPEATED,
current_timel_meas_timeout_handler...
I'm a little lost on the GPIO mappings from the code to the outside world. I'm playing with the UART example on the nRF6310 board. In the sample code, IO 16 is RX and IO 17...
Hi,
I am using ble_app_hrs application as a reference code.
in our case i have gpio interrupt for every 25 ms.
what should i keep BUTTON_DETECTION_DELAY for 25ms...
Does the lcd clobber the tmr0 and/or ANT ???
We just went through several days of working w/ ns on running ANT w/ RTC with a resolution of using sd_ calls.
Is the LCD...
Hi,
i am using nrf51822 custom board.
For our application i am using ble_app_hrs source code.
in that i have gpio interrupt for every 500ms, to get data from accelerometer...
For example, if I have a GPIO pin configured with low sense, and it goes low just before I call sd_power_system_off(), will the device return to System ON mode immediately...
Hello,
I've got a nRF51822 DK which I try to program with a SoftDevice using the nRFgo Studio (nRF51 Programming). My chip/programmer seem to recognized properly since...
Hi,
For developing our application i am using ble_app_hrs
in my case i have gpio interrupt for every 500 ms to get data from accelerometer.
question:
in heart...
Hi,
I am attempting to understand the timing of events when a mobile application connects to my nRF51822 based device. The reason being is that I have to enable the UART...
Hello,
Greetings, in the nRF24L01 datasheet, its mentioned that the module can work as a multiceiver, meaning 5 nRF24L01 module acting as PTx can communicate with 1 nRF24L01...
hi,
my customer using nrf51822 DK to have debugging software,the error occur in the attachment.
can you tell me something have Caused this problem?
thank you !...
I am using the code
err_code = sd_ble_gap_device_name_set(&sec_mode, (const uint8_t *)deviceName, nameLen);
I have made sure that nameLen is less than BLE_GAP_DEVNAME_MAX_LEN...
Hi
i am using twi_hw_master.c for i2c communication of accelerometer.
my accelerometer address is 0x18.
once i call
twi_master_transfer(0x18,dataW,1,1);
in...
