I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I'm using two nRF52805 to get sensor values and send 2 sensor real-time values to my phone via BLE. Each nRF52805 BLE works well (Individually tested by nRF Connect App. It...
The encoders I am using generating about 500 pulses per second, and I need to read 3 of them at the same time. I assume a good approach for that is to use the hardware timer...
Hi, working with NCS v1.4.2, I see building products for an <app> landing into subfolder <app>/build/, in several flavours
app_moved_test_update.hex app_signed.hex app_test_update...
Hello,
I'm trying to flash an example code from the SDK onto the Arduino Nano 33 BLE board.
I tried to use the external debugging on an arduino nano 33 ble card but the...
Hi,
I'm using NRF52840 and having a lot of issues with hard fault.
From time to time, I get an application crash with the following log:
HARD FAULT at 0x00000000 R0...
This question may be better suited for the Zephyr forum, but I figured I would ask it here as well in case somebody can easily see what I may be missing.
I am trying to...
I am attempting to use the UART peripheral with a UART device which communicates via 1 start, 7 data, 1 even parity and 1 stop bits.
Is there any? way to configure or fake...
According to this post it seems clear that a peripheral device cannot set the connection event length in a given connection (and only has mild influence on the connection...
Hello,
it's been a couple of days that i have a problem with NRF9160DK.
The problem is related to function getaddrinfo() that is now permanently returning -11, whatever...
Hello,
I wanted to interface LCD with nrf52840, for that we have selected few of them from different vendors. I was looking for display drivers for LCD, but couldn't find...
When building the zigbee network_coordinator example for the nrf52840 dongle the merge.hex is linked to start at 0x0 in flash so the nrf connect programmer won't flash it...
Hi everyone：
New to the DevZone, nice to meet you guys.
I have an problem to the GPIOTE.
I'm now using an AFE4404 to calculate the heart rate and heart rate variability...
Hello, teams!
I'm sorry to bother you.
Now I'm testing mesh function.
I have two questions.
1) Is there good way to show the performance of relay operation?
...
Based on nRF52840 datasheet, to configure the QSPI peripheral, it is necessary to activate the external flash memory interface using ACTIVATE task. Our problem here is, during...
