I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
We are designing the Nordic 52840 into a product and had some questions about the power configuration:
For both REG0 and REG1, are there any downsides to selecting...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
--
I use ble_app_blinky example and use nrf5-calendar( https://github.com/NordicPlayground/nrf5-calendar-example ...
Hi,
I am new to nrf9160 and zephyr. I was using the SD card and a breakout board on SPI bus to write the raw data coming from the PDM interface on nrf9160 Feather. Before...
Hi Nordic DevTeam,
I have successfully done DFU through nRF Connect both on Android and iOS after merging ble_app_uart (combine ble_dfu_buttonless application here) & secure_bootloader...
Hi,
I am developing projects for street lightning system and I use in my projects many CoAP libraries. In my projects I use OpenThread and some peripherals like UART....
Hi everyone,
I use the nrf5_SDK_for_Mesh_v4.1.0_src, I would like to reduce the time it takes for a device to connect to a bluetooth module as a proxy. For the moment this...
Hello all,
I try to get the asset tracker v2 to work against a eclipse mqtt broker. For the first steps I use the mqtt.eclipseprojects.io broker before I hosting my own...
We are developing a device with the nRF52805 for BLE communication. The firmware was developed for nRF52832 and converted to nRF52805 following Nordic's documentation. The...
Dear Nordic support,
Could you please give an advice regarding usage of Zephyr SPI driver / NRF SPI driver with Nordic nRF52840? I've faced with the issue that driver can...
Hi!
I've shipped a whole bunch of PCBs out to customers where pin P0.21 is attached to an IC (which pulls it low by default).
Usually this is fine as the preinstalled...
<install folder>\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.zip\examples\thread\cli\ftd\usb\hex
Need to get confirmation on if I follow the above path and flash the binary...
I have my first custom nRF9160 prototype boards back and they seem to be working pretty well. One question I do have is that I have been unable to find a clear concise description...
Hi all,
I would like to control a stepper motor over BLE. The motor takes STEP(rising edge) inputs for each step. The motor move is based on pre-calculated look up tables...
