I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi,
I have a huge issue with NRF52832 and DFU on custom board. I have a custom characteristic in my application to switch to DFU after proper PIN typing. Then I call this...
Hi All,
I'm trying send custom board(nrf52832) sensor data to DK by ble uart and multilink.
When I build the code in Keil. I got the message:
..\..\..\main.c(544): error...
I am using the light bulb example and connecting to the Zigbee2MQTT. The Z2M is running on a docker with logs level set to debug.
So from the light bulb example, how can...
Hi. So, pretty sure I've got the firmware installed right and plugging the dongle in creates a "/dev/tty.usbmodem1101" entry. Problem is I have a crash in Python:
This...
I am going to send a sequence of notifications and the documentation provides this information
The API functions that may consume an application packet depending on the...
Hello,
I am using the nRF52811 for my project. I am in the layout design phase...almost completed and I need some clarifications before I launch the first Proto.
I don...
I have found a lot of people having problems debugging with the SD enabled, but we are not using any BLE atm. We are just using the softdevice for OTA updates. But this is...
hi support team,
i just want to confirm, for mesh SDK, i can only find "APP_UNACK_MSG_REPEAT_COUNT" to increase message repeat count, for ACK message, i can't find any...
Hello NRF Team,
We are using nrf51822 chip for one of our product. Currently, we are using a GPIO connected to user button to Turn On the device from system off sleep mode...
Hi,
I have an issue with broadcasting Eddystone TLM + iBeacon, my project is based ble_app_eddystone example and nRF5_SDK_17.0.0_9d13099, SOC is nRF52832.
Beacon advertise...
Hello,
I am developing a circuit which is based on nRF52820. I got the boards manufactured but they are not functioning properly for some reason.
Following are the errors...
CHIP: nRF52840
SDK: Thread and Zigbee 4.1.0
SD: s140 using multiprotocol
Hi, I have developed zigbee end device.
The communication with the coordinator has be done...
Hi,
I'm using pc-ble-driver and a PCA10040 devkit. I'm having issues with using sd_ble_gap_data_length_update.
First, my configuration has ATT_MTU set to 247:
Then...
Hi! I've read a bit about the limitation of write/read cycles with the nRF52840. I the ~10,000 write/read cycles limit means after this many erases, the flash is no longer...
