I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello, We noticed that when we enable the whitelist, we can successfully filter out connection requests, but not scan requests. Our device still responds to every scan request...
Hello sir / ma'am
I want to implement OTA with zephyr using openthread but the size of my code .bin file is too much like 412kB .
How can I reduce my code size ?
What...
Hello
I am building a code with Openthread (NCS V1.4.0) and the size of that generated Bin file is 405kB. I would like to know why size of that file is more? I need to reduced...
Hi!
We are working with the nrf5340 on a custom board and we are trying to reduce its power consumption to the minimum possible. We have a beacon advertisement application...
Hi all,
I have just some issues with sd_flash_write and sd_flash_page_erase functions. I have created some code to read the temperature value and save this value in memory...
Hi,
I am considering nRF52 (most likely nRF52833 or 811 ) for a new design - curious how mature is the concurrent multiprotocol support in nRF52 - in particular for nRF52833...
Hi All,
We are using nRF52840 MCU and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71. We are designing a device that uses switches connected to the below pins,
Pin...
Hi,
I use a custom board, softdevice and boot loader.
I use DFU to update a slave chip firmware. Everything goes right until we invalidate and write flash :
// Invalidate...
Hi
i use sdk 17.02
custom board
soft device
when i program input digital pin I have an extra consumption of arounf 9µA versus not using it.
Could you tell me if...
Hello,
I am using FDS successfully with SDK 17.0.2, secure bootloader and softdevice. Bluetooth (BLE) environment, if it does matter.
I can read and write data. But following...
hi guys
i develop mobile app for iOS and use nrfMesh lib v3.0-beta1. i have few nodes subscribed to a group. I send GenericLevelSet message to a group and receive successful...
if a response to the http request is chunked ( https://en.wikipedia.org/wiki/Chunked_transfer_encoding ), it is not handled correctly by the serial_lte_modem.
Sometimes...
This should not be so hard - have to go here and wait until this gets answered.
1. I can't find an SDK consistent with SoftDevice s110.
2. I have an nRF51822 production...
I want to find out BLE throughput.
Throughput_bps = num_packets * (ATT_MTU - 3) * 8 / seconds.
In this equation, how can I find out num_packets?
Also, ATT_MTU =...
Hello,
I was just wondering that if somehow we can send the AGPS code data of thingy 91 to adafruit server through the MQTT just for testing purposes.
Let me know...
