Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
I'm trying to diagnose frequent (80%) DFU failures that I'm seeing with our Android application using Buttonless mode.
Our target can be 100% reliably updated with our app...
Hello,
I would like to program the NRF52840DK to send ZigBee beacon(not beacon request) to the end devices, but I cannot seem to find the API, etc. to do so.
Or perhaps...
Hello NRF ,
I am not able to run any of the the BLE peripheral example codes from the SDK12.2.0 ( Nordic NRF 52 SDK ) .
The reason I am using 12.2.0 is I have a sensor...
Hi,
I need a battery calculation in my project, For that I need to implement ADC.
But in SDK17 their is no ADC sample example for nrf52810 is present. So please suggest...
Hi Team,
I have nrf52840 DK board and is trying to get the prints from nRF USB port using cdc_acm application. I can see the prints when I connect the DK board with the...
Hello, I am trying to set the company ID and manufacturer specific data in the NCS SDK using nRF52840 dev board
I have the following array of structure
uint8_t COMPANY_ID...
Hi,
I am trying to generate unique key(s) for every device and store them in Optiga to sign the messages, among others. After generating the key pairs, I need the private...
Hello. Currently, the Samsung Galaxy A series has a problem that UART communication is not available.
I want to find the cause and solution of this problem, How can I find...
I am using nrf52852 with sdk 16 version and I want to set the BLE connection interval via BLE command using an customised app. what i want to do is this
#define MIN_CONN_INTERVAL...
HI, I'm developing a device (based on uBlox Anna-B112 with nRF52832) that must securely store three 256bit keys. These keys must remain secret and must not be readable by...
Hi,
I'm just starting out with zephyr on a nrf52dk (nrf52832) and I'm in need of performing some math functions on the data output on a mpu6050.
The MPU6050 is spitting...
We are developing couple of products based on nordic 52810 and 52820. Mainly 52810 And we have received very good support from nordic team and very promp and pro-active support...
The documentation is unclear about QSPI handling:
If I issue a QSPI erase command then I receive confirmation that the erase command has been written to the external QSPI...
I'm using FDS module from nRF SDK 16.0.0.
Below I'll describe issue which I'm experiencing when trying to initialize FDS twice:
To be sure that my FDS filesystem will...
Was going through the process of updating the modem and application on my just purchased Thingy-91. Initially the programmer reported that the processor and two serial ports...
