I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
According to this thread, GPS sensitivity of Thingy:91 does not seem to be good while I haven't tested this yet.
https://devzone.nordicsemi.com/f/nordic-q-a/51424/thingy91...
Hello.
I have found this document and have a question.
In according with document below: service " Generic Access" (UUID1800) has a few characteristics: " Device Name...
We're attempting to get a Bluetooth data stream set up on our nRF52840. We've taken Zephyr's peripheral sample and pared it down somewhat to only allow indications from the...
Hello,
I am working on LPN node code from the mesh SDK 3.2.0. When I run the example code, I see a current peak at every 2 sec interval. Please check the image attached...
Hello,
I managed to flash the AT command client to the board and connect to a network (both verified by COPS and CEREG)
Am I right that there is currently no AT command...
Hello,
We start using of our BLE devices with more or less permanent connection with our central BLE device, it was needed for Alisa connection.
BLE peripherals are old...
Hi,
I am a beginner in nRF52840. I want to add a channel hopping feature in the 802.15.4 example .
As per my understanding of source code, we can set the channel number...
I am looking for a way only a known/trusted device can connect and write/read information from my device. Filtering by address(white-listing) is not feasible. So what is a...
Device:
Peripheral only
Peer Manager and Bonding working
S140 radio
nRF5 SDK 15.2.0
Rigado BMD-340 module
Central == iOS devices
Our nRF5 module is controlled...
Hi, I'm on last step of developing, but I have this critical trouble. For the project, I started from ble_app_buttonless_dfu sample of SDK15.3. I added some peripheral (one...
I'm using the ble_app_grs_freertos example. I'm trying to maximize its thru-put potential for Central devices which can support the high data rates. For this I've used the...
Hi, guys,
What I do:
Add freeRTOS into ble_app_hrs example project in SDK15.0
What matter I get:
When I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE as 247, the device can not...
