Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
Hi Nordic Team,
I'm using nRF52832 DK.
Please suggest any example code to read GATT service(Device information service) by a central device. Please help as soon as possible...
Hello, recently i have my computer changed to a new one with Windows 10. So yesterday i have performed an fresh new install of NCS and Segger with [ Getting Started Assistant...
Hello, I am compiling an application to be flashed onto a nRF52810. I am using Segger Embedded Studios and the nRF52 DK to develop the application. I want to read values from...
Hello All,
I have nrf52810 chip. using softdevice 6.1.1
I have implemented dfu feature.
Now i have implement tx power change feature through nrf connect mobile app...
Me and my team have been working for a couple of months on a custom firmware code for nRF9160 on a custom PCB, based on mqtt_simple and asset_tracker which basically reports...
I have been working to get the secure_bootloader examples to run on the NRF52832_XXAB (QFAB with 32kB RAM and 256kB Flash).
Apart from the fact that I had to change the...
Hi,
Good day!
Problem statement:
TSM12 Capacitive touch sensor IC (I2C com supported) is used in our application. It has got 12 output channels and Channel 1 is a parallel...
I am trying to send a string from the board through uart to the PC(windows) through usb-ttl. I tried using adruino and was able to successfully execute it. but when i tried...
Hi,
I've used the 'Getting Started with nRF9160 DK' tutorial to setup a development environment, I have a problems with loading asset_tracker project. My output:
Loading...
I understand there is a hard fault happening in the SDK. I am using SDK 15.3.0, I am not on a sdk example, but on a specific program I am doing I can't share. It happens a...
Hi,
I added a small shunt resistance to see current consumption of nRF52832.
I see current ripples when DCDC regulator is enabled, this ripples doesn't exist when DCDC...
1. We are running our nrf52832 based project on Eclipse and are able to compile, build and run the project on our target hardware. So far, so good.
2. Now, in addition we...
I'm working with the light switch server example and nRFMeshProvision example project for iOS.
How do you send arbitrary data to a board? I understand the provisioning process...
Hi,
I noticed that there are a few methods in nRF52 SDK v16 to blink LEDs:
Use bsp indication methods which seems based on app_timer;
Use led_softblink library which...
nrf52832, SDK 15.3
The average current consumption is 9.53uA in my system with SPIM. After I init another SPIS, the current consumption goes up to 478uA. CS pin keeps high...
