i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi all,
I am working on a project where the requirement is a sensor collecting data and sending to the NRF52832 via UART. Every 40ms, the NRF52832 will receive 40 bytes...
As we would expect, sd_ble_gattc_hv_confirm returns BLE_ERROR_INVALID_CONN_HANDLE when the conn_handle argument is invalid (i.e. does not represent an active connection)....
Can anyone tell me if the ble_app_hids_keyboard example will run OK on the nRF52810?
I'm currently using the Rigado BMD-340 (nRF52840) and my project is based on the keyboard...
I’m a new user in the BLE world. I’m trying to play with a nRF52 DK and I’m facing with a problem. I tried different IDE (VScode + platformIO, Mbed studio) with the framework...
I ported the nRF52840 USB driver to work with Mbed-OS's USB Device stack. When building without the soft device, the following macros are removed from the compilation:
...
I'm trying to read two ADC channels asynchronously.
I can setup two channels, and as mentioned on the forums , the data from channel 0 is at buffer[0].
The issue I'm...
Hi all
I want to check my nrf52840 custom certification.i need to do radio test in my custom board.They are asking direct test mode with PSRB9. I m using direct test mode...
Hi, I created a simple project using the nRF52 SDK, to which I later wanted to add BLE support. I used the ble_app_blinky example from the SDK as my starting point. The example...
I have compiled asset tracker example and it worked on 0.8.2 version of board but not on 0.8.5 board.
1) Is there anything which should be made differently in software for...
Hi, I'm trying to measure the current of my nRF9160 DK (PCA10090 v0.8.2) and have some problems. In respect to the following thread (https://devzone.nordicsemi.com/f/nordic...
Hello. Project im developing requires low power wireless encoder. NRF52832 is a really impressive chip that handles everything i need within 40uA. But I've got problem with...
hi, we delevoppe a card with a module which is use your nRF52832 IC. I check in your document information relative to IO hardware, but i didn't find any information concerning...
I am writing some code for a customer using the nrf52840.
The Softdevice asserts immediately after a call to nrf_fstorage_write().
The write address is OK, alignment...
whenever I use nrf connect desktop app in my Linux system for power profilling.
The power profiling kit doesn't start and keeps on giving the same error
There are similar...
