I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I am trying to set up a humidity sensor over I2C and I'm trying to use the twi interface. There are examples where the app_twi interface is used. I am however unable to get...
I'm working with a development prototype board with the nRF52832. It is connected to a main processor in our design over UART. We are working towards being able to do the...
Hello Nordic team
I am working on nRF52840, SDKv-15.0.
Is there any example code available which can send message from central device to peripheral device apart from ble_app_usrt_c...
Hi,
I'm tring to enter DFU mode by combo keys by KEY_COMBO_TWO_KEY_REGISTER().
In v1.1, I used m_pwr_mgmt_shutdown(M_PWR_MGMT_SHUTDOWN_TYPE_DFU) to enter DFU mode directly...
I'm looking at decreasing the motion sensor update rates for the Thingy:52 to get less frequent readings into the sample app. I have seen in the MPU9250 specs that I don't...
Hello Nordic team
I am working on ble_uart_c central example on nRF52840 DK, SDK v-15.0.0. Example code working correctly I can exchange data between peripheral and central...
Hi I am trying to reduce the power consumption of the badge of my company as much as I can. We use a proprietary radio protocol on the nrf52832.
I'm currently developing...
I have SD and BL secure flashed to the device, and now trying to get the second part of buttonless_dfu + app with settings flashed next. After flashing the second part, DfuTarg...
I'm attempting to optimize our application for battery life on the nrf52832.
If I execute a floating point calculation to rescale RGB to PWM, I start drawing 6.2mA, eliminating...
Dear all,
We are programming the FICR and have found very little documentation on the random number generator fields: - TRNG90B.BYTES - TRNG90B.RCCUTOFF - TRNG90B.APCUTOFF...
Hi
I have followed this example: https://github.com/bjornspockeli/custom_ble_service_example through to the end, but am now having issues with some intermittent behaviour...
I need to transmit and receive beacons using nRF51 DK. I saw a few examples in the SDK ble_beacons where we use the app, but I need code to transmit and receive both using...
I am trying to send 'h' or the number 1 using vendor defined page (custom HID descriptor). How do I do it?
NOTE: I have worked with hid mouse & keyboard examples and also...
Hi,
I am trying to make a network of four Nordic Thingy: 52 IoT Sensor Kits by using the nRF52 DK to program them. Then, the readings for the 4 senors should be displayed...
