Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hello everyone,
I following the exmple about advertising
devzone.nordicsemi.com/.../
It advertise a string (line 142 in main.c). I want to replace this string with...
Hi,
We have updated our code to the last sdk version (nRF51_SDK_9.0.0_2e23562) and we cannot upload the application code anymore with the nRF Toolbox on our iPad. However...
Hi there, I'm having some truble to understand how to set a synthetice 32khz clock from the 16Mhz external crystal. Right now I have the next code working fine:
NRF_CLOCK...
Hey guys,
I’m trying to send a single non-connectable beacon every few minutes in the lowest power way possible. nRF51822, SD S110 8.0, SDK 9-2. Different scenario from...
I am experiencing a fault at sd_flash_page_erase() in the sdk_nrf51 ble examples.
Softdevice 8.0.0 is loaded and is from the sdk_nrf51 bundle.
Both the ble_app_proximity_s110_pca10028...
Here is my power consumption (3.0V):
no app_pwm: 0.010mA
after app_pwm_init(): 0.295mA
after app_pwm_enable(): 0.891mA
If I do app_pwm_uninit(), power consumption...
NRF52 on-site training for today, know BLE pairing use OOB way will be a little bit more simple and safe, and then want to ask next, on NRF51822 platform have the corresponding...
I'm using a dev board based on the nRF52832.
The majority of the time the RSSIsample register returns the correct value.
However sometimes the value returned is 0x7F...
The Product Specification makes it clear that the given levels of accuracy for ADC measurements are only possible when using an external crystal for the HFCLK. We have one...
Hi Nordic,
Running a gdb session on nRF51, it is difficult to debug the code beyond the SoftDevice initialization. Then, I have to step through with (gdb)ni, but this is...
Hello everybody,
I used to my PCA10028 DK board with nRF51-DK-mbed-IF but I wanted to revert for nRF51-DK-J-Link-IF. According to the nRF51-DK - User Guide v1_0 documentation...
I have the code below initializing TIMER1 and and IRQ every 1ms. I call app_sched_event_put within the timer and I get a Hardfault.
Any hints on what is going on ?
Thanks...
