Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
Hello Nordic.
I find two RNG example.
Both nrf_crypto_rng_vector_generate and nrf_drv_rng_rand , what is the difference?
Which one is better on RNG.
How to correspond...
I am trying to set up developing environment, and however I couldn't download and install version 7-2018-q2-update of the GNU ARM Embedded toolchain.
Would you please guide...
In my application i need to use NBIOT network & GNSS.
For that i found that i need to configure AT%XSYSTEMMODE=0,1,1,2.
But i am not clear on what should be configuration...
Central info SDK: 15.3 nRF52840
Uart communication is used. In rare cases, the value obtained by checking the waveform with an oscilloscope was different from the value...
Hello everbody,
I readed alot about the nrf52480 "how to flash softdevice and the other stuff", but i cannot get the ble_app_gls working out of the scratch.
I have the...
Hello everyone, I am trying to implement audio processings algorithms with my nrf52DK.
What i need to do in order : 1- Sample my audio signal ( It will be guitar sound ...
I need to use a nRF52 chip to handle interrupts with low (and known) latency. Basically, there are specific ~100 us long intervals during which I need interrupt latency to...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Hello Devs,
I am using app_timer to create multiple timers to read different sensors
Currently, I have 5 timers created using app_timer_create, each timer has their own...
I use nRF Connect for Desktop to download hex file(nrf52810).
Use the following example：
nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble + nRF5_SDK_15...
Hi,
How do i turn off the nrf power management library? Is there any function like nrf_pwr_mgmt_uninit()?
The reason i want to turn it off is because it causes the usbd_msc...
I have a requirement for BLE and 802.15.4 stacks in a multiprotocol environment. I have looked at the sample at NordicSemiconductor/nRF-IEEE-802.15.4-radio-driver on github...
I am trying to initialize the RTC and trigger an interrupt every 10 seconds, and I am unsure of why the code above is not working. I followed a similar method to initialize...
Hi,
I'm working with the nrf52840 and spi mngr to talk to a SPI flash memory (AT25SF081). I use nrf_spi_mngr_perform to send a command to read the manufacturer ID
...
