I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi
I have made beacon using nrf52 dk
when i measuring power consumption after upoading firmware without removing power it minimum power consumption is 12ua when not...
Hi,
I’m currently trying to design my own pcb based on nRF52 Development Board. I went through a number of pcb files and all of them are associated withnrf52832 without...
i use the keyboard project, bond and pair the iphone7(ios11.2), the iphone display is connected,ok, then i reset the keyboard and erase bonds, the iphone display disconnected...
Hi Dev Zone,
I am attempting to flash a blink led app, based on Zephyr (nrf52_pca10040), to the primo core (contains Nrf52832), through Jlink debugger on a Linux machine...
At what voltage should DCDC be manually turned off for a nRF52832 ?
This thread for nRF51 says:
You must manually disable the DCDC when supply voltage goes below...
Hello,
I followed the steps mentionned in this blog
I did all the required step but I'm still seeing the same behavior.
below is my setup :
I'm using nRF52840 and...
Hi folks,
We got a weird behaviour with our nrf51822(SDK 12.2.0, s130) device. we have built a low power application with following parameters:
MIN_CONN_INTERVAL...
I have tried to understand how data was send from two BLE device. I have had 2 PCA10056 board and I have loaded ble_app_blinky example and ble_app_blinky_c example for each...
Hi All.
I have one question.
I just want to send "volume down key" simplely after connect with android device to take a picture.
I have no idea. and I don't understand...
I modify nrf51 nus in SDK12.3.0 to realize my application, I found when enable uart, the consumption near 830uA , and then call app_uart_close(), the consumption near 5uA;...
Hi,
Is there and C/C++ source code to get float value from 32-bit ieee-11073 FLOAT data type
I need c/c++ code to parse 32-bit ieee-11073 FLOAT data coming from FORA...
Hello,
Using Spi bus with frequency = 4Mbps give me this deformed signals (clock and miso) and when I push it to 8 Mbps I am not able to get the correct values.
Obviously...
When an event is bound to the ppi channel, and this channel is bound to both task_capture and task_clear
can I get the correct COUNT value when an event occurs?
Or can...
Hi all,
I wanna build a IOT gateway. I follow this steps infocenter.nordicsemi.com/index.jsp
When I access coap://[ipv6] It dont have resource light, just only have...
[SDK 12.3.0 / nrf52 DK / Keil tool / beacon example code]
Hello. i am a novice developer.
Power On - Beacon data transmit and enter to sleep mode after 10 sec
...
