hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hello, Everyone.
I'm developing a beacon to check the battery level.
I'm current using
nRF51822
SDK11.0.0
Softedevice S130
My inquiry is nRF52 series is...
We just received a batch of custom boards containing the nRF9160. I would like to test them and start developing our actual application.
So far I have switched SW11 to match...
Hi everyone.
I'm using pc_ble_driver_py with nRF52840 USB dongle with burned connectivity_4.1.1_usb_with_s140_6.1.1.hex.
pc_ble_driver_py is modified by me to support...
Hi,
Is there anything to match the above subject with SPI ?
The coding for sending and receiving should be written on the both sides of sensor driver and master side?...
Hi,
I am looking for documentation about the reflow process of the nRF9160, but I cannot find it on the documentation webpage. Is this information available at Nordic? I...
Hello.
When Notifying about 100 bytes of data, sd_ble_gatts_hvx() is sent 5 times. Occasionally NRF_ERROR_RESOUCES occurs. Currently MTU_SIZE is 23, and the actual data...
based on the comments in sdk_config.h, the softdevice uses priorities 0, 1, 4, 5. yet in app_util_platform.h, the macro _PRIO_APP_LOW_MID is given the value of 5. is this...
Hello
I need to do pairing with Android devices without passkey in ble_app_uart example.（ Device nRF52832 ,SDKv16.00, softdevice S132 )
I use ble_app_gls example and Android...
Hi
I am using ble_app_blinky but led is not blinking. I am using P0.27, P0,28, P0.29 pin for LED but in program pin of LED are define as
#define BSP_BOARD_BUTTON_0 0 ...
Hi to everyone. I'm starting developing a bluetooth LE application based on the new Nordic SDK using Zephyr.
I currently have two nrf52_pca10040 boards and I'm trying to...
Hi everyone!
After defining a variable as no_init , my intention is to update its value along the program to debug what was its last state before a random reset.
I am...
Hi !
I am on SDK 15.2 and NRF52832. My peripheral device is on BLE5 and my Central is on BLE4.
I have read that extended advertisement ( up to 256bytes) is a BLE5 functionality...
Hi,
I followed the nRF52840 USB Dongle Antenna has reference layout. I have a small doubt of Antenna matching capacitors(c3,c4,c26) and inductor Should use the same package...
Hi all, I am combining MESH SDK 3.0.0 light switch example client and server with SDK 15.2. I have combined some server code to client and there are no error. And I can use...
hello,
We have developed a custom board corresponding to mbed pca10024 evaluation board.We haven't mounted the rf section and not even the crystal.The only thing that the...
