I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello Nordic Team,
Currently I'm working in a BLE HID Project (joystick with 16 buttons and 2 axis (x and y)) usign a NfR52832 and modifying the hid mouse example from SDK...
Hi,
As well know, the nrf52832 had build-in a battery level detect function. It can get battery-level by following program
Would you please tell me how to design it...
Hi
When I finished the program and read back, I saw that there was unintentional data at 0x2D000 and 0x2E000.
I used up to 0x26000 addresses. Where is this memory used...
I've taken the basic examples/peripheral/blinky code and tried to add the logging module to it. For some reason the only time I can get the application to run and log correctly...
I am developing a firmware application that needs simultaneous central and peripheral role. I am using sdk 15.2.0 and was experimenting on dev board PCA10040. I have taken...
Hello,
I want that nRF9160 goes into PSM on boot until a button is pressed, do someone have a good link about PSM please ?
How can I do a software reset with a clean lte...
Dear people,
I use a pca10056 (alternatively the pca10059 dongle) and have compiled the connectivity firmware as described on the github page (release 4.1.1).
The only...
I use nrf5_SDK_for_Mesh_v3.2.0_src\examples\serial and board pca10040.
Supported commands.
In [2]: for i in range(0, 10): send(cmd.Echo("Hello: " + str(i))); time.sleep...
Hi, I'm reading the nRF5340 OPS v0.5.1 document and in section 3.2 ("Memory") there is a reference to "256kB of peripheral RAM". However, the document doesn't explain what...
Hi there,
I'm working on nrf82382, try to use COMP function to monitor the voltage of AIN0(p0.02), but seems not working, no example for the COMP. and then I found the...
We enable TX notification of NUS service with bonded iOS (iPhone), iPhone constantly sends TX_READY command until disconnect.
Can you confirm this is correct behavior. ...
Hi, I am working with the adxl362 sensor and the nrf9160 SPI example ( https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/spi/src/main.c ) and...
Hi, I am working with the adxl362 sensor on the Thingy91 and I want to set the trigger of the sensor to a specific value.
In the datasheet ( https://www.analog.com/media...
Hello everybody! I'm developing an application using CMSIS DSP library, so i included about 20 math files and using finctions from these files. After compiling i get a linker...
