hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hello All,
I am working on NFC using nRF52832 chipset .
I followed the below this link for http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
Hi everyone :D
I'm not being able to compile a c++ code on segger embedded studio.
The same code compiles with the Makefile provided in the SDK 14.2, but not with the...
Hey, we are using the nrf52840, and the SDK 14.0.2 and the uart example. We need to set the BLE range to max, and therefor the TX to 8db, the transfer speed to 125kb/s. We...
This is my second attempt at merging a pure UART App (no soft device) into an App derived from the ble_app_template (with soft device)
I see I am not alone in having suffered...
Hello everyone, I would like to make an unconnected broadcaster to send data to the advertising channels ... I come from a X-NUCLEO-IDB05A1 board and that's has been pretty...
Hi
in the release notes of the SDK14.2 the following is written
The following toolchains/devices have been used for testing and
verification:
- ARM: MDK-ARM version 5...
I have written an interrupt program to blink an led at port P1.01 by pressing the button 1.So i added the code in ble_app_blinky example so i can blink the led from the board...
I want to read integer data on the cloud
for example int a=1001;
This value must be displayed on the cloud service after every 5 seconds.Also i want to increament the value...
I urgently need to decide on the use of the chip in future developments and deliveries. There was no problem with the 51822 chip in the connection between 51822 to BlueGiga...
We are working on an IoT application using the nrf52840 Preview DK and would like to interface an external Wifi Module for transfering the acquired data to the internet. Could...
I am using SDK 14.0.0 with Softdevice S132 V5.0.0 and the accompanied DFU libraries. In the examples\dfu\bootloader_secure_ble example I think the logging system has a problem...
Hello,
When I try to read data from UART RX port using serial library, I'm not able to read the data beyond the number specified by
SERIAL_FIFO_TX_SIZE and SERIAL_FIFO_TX_SIZE...
Hey, I'm using raspberry pi 3 model b, with the rasbian strech os running in it. I have followed the tutorial provided by nordic using this link for BLE over IPv6. When I...
Hello, In my case, i'm using some PTX and one PRX. It's working well. Now i want to extend coverage, can i use repeater/forwarder? I tried but have problem with PTX: after...
