hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Dear all,
I have been working with a nRF51422 device for about two weeks, and everything went good.
This morning, out of nothing, i got this error in IAR: Warning: Stack...
Hi,
I have disabled the reset functionality of SW5 on nrf52840 PDK by giving the following command
" ./nrfjprog --recover -f" as it is mentioned in PDK document.
Now...
Hi Nordic devzone,
I'm wondering if you guys at Nordic are willing to release the source code for the mbed interface binary for the ATSAM3U2C. The current version of this...
Hello
I have a problem with my code implementing BLE NUS peripheral. Program hangs in the function sd_softdevice_enable. I have tried with external oscillator and with internal...
My previous product uses an empty notification to indicate that a bulk transfer is finished. I attempted to send an empty notification but got error code 0x10 (NRF_ERROR_INVALID_FLAGS...
I'm using the pstorage driver on the nRF51 to maintain several NVM variables. The NVM functions correctly and maintains state between power cycles. However, when I reflash...
Hello to all Nordic jedi masters!
I am using the nRF52832 along with SDK v11.0
I want to have the SAADC generate events only when the converted value is above a certain...
Hi all,
I am using a nRF52-DK board to receive data from the USB port using Serial, and transmitting it using ESB to a second board. If I use either Serial or ESB individually...
The latest rev of the product spec (1.1 when this was posted) includes a table on page 77 that indicates that the System OFF draw depends on a wakeup source (e.g. GPIO, NFC...
while i open ble sniffer , it sucessfully recognizes the nrf51822 ble nano but when i press w to open the wireshark, it shows no packets and in the interface list it shows...
Example ble_app_uart compiled in Keil 5 O.K but the resultant HEX file in the build folder is only 34K whereas the hex file in the hex folder is 335k. I followed the tutorial...
Hi Nordic team,
Very impressive demo posted on the blog zone this week! I'm trying to understand the details and sorry if I ask something what would be visible in the source...
After upgrading to iOS 10, I have been unable to successfully interact with my device using the NUS. I used to use the NUS to communication with the device and retrieve stats...
Hi, my setup is:
nRF52 DK PCA1040 v1.0.1;
Adafruit MAX9814 electret microphone amplifier;
My project concerns about:
Sampling audio from the board with...
