I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello Nordic Experts,
I am developing the pairing in a central. I am working on nRF52840 DK with nRF5_SDK_15.2.0_9412b96 as the cnetral and I have an iOS app as the peripheral...
We are using the nRF52832 with S332 v2.0 of the stack. We have recently been testing concurrent operation of a BLE peripheral connection and an ANT bidirectional master. The...
Hi all,
I'm using nRF52840 Development Kit and Nordic SDK v15.2.0 with soft device v6.1.0
I'm using ECDSA Cryptographic libraries for a BLE related project. I want to...
Hello,
I am working on Low power and Ultra Low power.
I am using the nrf52832 chip as well as the breakout board. In SYSTEM-ON mode power consumption around 6 mA and in...
How do I calculate round trip delay (time taken for packet to travel from peripheral to central(PC) to peripheral again)? Is the existing time calculation in the example code...
Hi,
I have some troubles using TWI easy DMA. I set EASY_DMA flag to 1, but I can't see any results in my performance tests. Can anyone explain me the required steps? ...
I am looking at the android version of the Blinky application and was trying to make some modifications to enable the LED3 on multiple boards (peripherals) to turn on from...
Hi,
In a peripheral, a notification is sent to the central every 10ms. (payload less than 20 bytes)
I use : radio_notification_init(6,NRF_RADIO_NOTIFICATION_TYPE_INT_ON_ACTIVE...
i want to read the temperature ..... my temperature data is executing from 0 degree temperature ...is there any way to execute only actual data instead of starting from 0...
I'm probably not using the good terminology here... let me explain my application.
I have an existing board which has all the logic implemented in an STM32 MCU. I now need...
Using Softdevice 132 version 6.1.0 I issue the request for scanning by calling sd_ble_gap_scan_start() with: ble_gap_scan_params_t scan_params = { { .extended = 0, .report_incomplete_evts...
Hi all,
I want to measure higher frequency (8 MHz) count/ticks by using the lower frequency (32 KHz) is there is any method to do it or any examples.
I want to measure...
Hi,
I am evaluating the nRF52840 with the Segger IDE.
I am about to experiment with Bluetooth, but I have a hard time understanding the different protocols/softdevices...
Hi, recently I've been confronted with this issue that all of my stocked nRF52832 ICs would not work with the lastest SDK, which later turned out to be engineering samples...
In the light of recent news like this one, https://arstechnica.com/information-technology/2018/11/bluetooth-bugs-bite-millions-of-wi-fi-aps-from-cisco-meraki-and-aruba/ ,...
