void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
When I was studying Zephyr, I found that some of the enumerations used by Nordic couldn't be found in Zephyr, so I was wondering if Noridc had encapsulated them in Zephyr...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I would build the Matter nRF Connect Lighting Example Application from the SDK for the nRF54L15-DK. Coud you add support for it in the Matter SDK?
Regards
I am developing a custom USB module based on the nRF54L15 chip. I would like to know how I can initially flash firmware onto the board.
My plan is to have a custom bootloader...
Hi,
I'm working with a custom PCB, with nPM1300 and a microcontroller.
The problem is that working only with battery the nPM1300 VBUS pin show 2.4V and I cannot put...
Hello community,
I have been using my PowerProfilerKit2 successfully under Windows10 for several years now.
Currently I migrate my main system to Linux and would like...
Hello. I have developed a custom board with nrf52840. I am trying to get it running using a bluetooth hids peripheral example in nrf connect v3.1.0. And the main() runs just...
Hi,
I have a field application with a gateway (central) that connects to multiple peripherals for continuous data streaming, in this case 10 peripherals. I notice sometimes...
Has anyone successfully managed to control an led strip (WS2812) with nRF52840's I2S by any chance? I'm trying to use the led_ws2812 sample ( docs.nordicsemi.com/.../README...
Hi,
I'm working on a custom project and I was able to add and edit the overlay file according to my need till yesterday. Today when I tried to build the project I observed...
I am currently working on a Direction Finding project, but I am facing an issue in prj.conf .
I use an nRF52811 custom board for Direction Finding. In the board selection...
I am following the tutorial on Nordic Dev Academy I have a nrf7002dk board and I flashed the code present here . The problem is even if I configure only one channel and I...
Hi Nordic,
I am currently working with the nRF52833 development board and facing an issue related to the APPROTECT feature. Each time I connect the board, the access protection...
HI ALL,
v2.8.0, nrf54l15, using the "periphral_uart" demo without any modifications
I downloaded nrf52840 using v2.8.0 and it runs normally, but nrf54l15 has issues. ...
Hi there, I am trying to implement a UART handler on my nRF9151 that can Tx GNSS updates to my nRF52833. I am adapting this into the cellular/gnss sample, which is working...
