hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
We are developing a system in which a device controls a host and the device should receive status information about the host. In some use cases multiple hosts are...
Hello everybody !
I am looking to connect 2 cards nRF52 DK (52832) with another card nRF52 DK (52832), a little like the fact my smartphone with these 2 development cards...
Hi, all.
I'm making a mqtt client with nRF52832.
All examples of SDK 14.2 were using PSK secure.
But I want more secured connection as like MBEDTLS_TLS_RSA_WITH_AES_256_CBC_SHA...
Hi,
After sd_ble_gatts_hvx() call, is it possible to change or delete value in softdevice buffer before a connection event ?
Thanks by advance for your help
Best regards...
We have a medical products need to evaluate the maxinum transmission data rate of BLE .i am using is the latest nRF5_SDK_15.0.0_a53641a.
i find to using the ios lightbule...
Dear Developers,
Good Day!!
I want to merge ble_app_att_mtu_throughput & uart example, basically requirement is CLI & other UART communication should work together.
...
See a new landing page on the nordic website for the nRF52840-DK (as opposed to PDK), which states that..
"The nRF52840 replaces the nRF52840 PDK which is not recommended...
We are fine tuning our manufacturing process placing the nRF52840 and would like to know what surface finish is used on the chip. I was not able to find this in the spec.
It seems like a similar IAR debugging problem has been solved but after a day of trying everything...
BLE application with SDK 6.1 and SD 310 1.0 running IAR 8.1 (and identical...
Hi!
Thank you for providing an SDK for BT mesh so early. I'm wondering if you also provide an Android (or perhaps iOS) mobile app that interacts with BT mesh, e.g. by acting...
Hello,
i'm a french student so i'll try to do my best to talk in english with you. I'm trying to use and understand the nRF51822 in order to transmit data to a smartphone...
Hi Expert,
why BLE_APP_UART example can use button 1 to button 4 to wakeup from sleep?
I checked source code I only saw the BTN_ID_WAKEUP is 0.
#define BTN_ID_WAKEUP...
Hi, according to the Bluetooth Mesh Glossary , there are 4 features supported:
1. Relay;
2. Proxy (GATT);
3. Low power;
4. Friend.
Questions:
- Which of these...
We are releasing a firmware update which adds an additional bluetooth profile. Since we do not want or can retest the entire stack, we use a Previously Qualified Design (51744...
