here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi there,
My nrf52840 DK seems dead. I want to recover it.
What I did:
Put the nrf52840 DK into Bootloader mode by pressing the "IF BOOT/RESET" button while powering...
Hi,
I'm working with pc-ble-driver and a PCA10040 devkit.
First, the central sends a data length update:
This returns no error (0), and on the BLE_GAP_EVT_DATA_LENGTH_UPDATE...
Hello,
we have a question about the usage of FDS. The data to save has a length of 1200 words. So the virtual page size is set to:
#define FDS_VIRTUAL_PAGE_SIZE 2048...
Hello,
I am using "pheripheral heartrate" example on SES, but I can not integrate SPI or ADC. How can I add "nrf_spi.h" and "nrf_adc.h" and relative C files on that project...
I'm using an NRF52811 and trying to configure the UARTE for Tx & Rx at 57600 baud but I'm having trouble with the Rx. I think I am dropping bytes and so want to try and exploit...
Hi,
please find attached some patches to improve the code quality of the SDK
1. Make ble_db_discovery_evt_t a const ptr
2. make p_string in ble_nus_c_string_send...
Hello,
i just loaded compilled peripheral_uart project without modification from nrfConnect sdk v1.5.1 to nrf52840 of the nrf9160 dk
and here is the output on uart output...
Hi, I successfully implemented a custom BLE service using this tutorial from Nordic. Also, thanks to a Nordic engineer, I have the QSPI example merged with the ble_app_template...
Hi,
When I open an example project in the Segger Embedded Studios I can first build without a problem. When I change the target
device under Debugger in the project options...
Hi,
I'm struggling to adjust the BLE_blinky example in the Segger Embedded Studio from the NRF52810 to the NRF52811.
I tried to follow the documentation from here (...
Shalom!
In my central nrf52840 board we connect to a TI BLE sensor that has a customer UUID base service and the TI OAD base service both with 128 UUIDs. I succeeded in...
Hi all,
In my project am sending ecg values over ble to android app. During first connection, the values are received and seems to be no problem, but when i disconnect and...
Hello,
I want to increase the number of peers stored in flash. Right now I have FDS_VIRTUAL_PAGES as 3. If I increase this, would I be able what I need? I just need 10 pages...
Hi guys,
I have a problem opening CMSIS Configuration Wizard, but only in Mesh SDK. Because I am working in this SDK, do you maybe know how can I fix this issue. I checked...
Hi, I was testing NCS v1.5.0 and Azure FOTA application and found a bug in the is_update() function
If the current firmware version is shorter than the new one, it may...
