Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
hello Nordic
i am working with nrf52840, sdk16, over the peripheral app_ble_blinky example
my system will go to sleep mode for 10 minutes each time, i wonder if there...
SDK: 4.1.0
Hi, I want to send change notification. so I writes below this.
Some buf_id has got failure in zb_zcl_ias_zone_set_status.
So I added loop which get...
Hi,
We are working on a board with nrf5340. We are running the nrf5340 in normal voltage mode. So, we have connected the VDD lines to 3.3V. Since we are using USB signals...
how can I put nrf52832 in the system on sleep mode on advertising timeout?
Currently, on timeout, the device is going in system off mode and restarting on interrupt.
Hello,
I noticed that you improved the hardware design in version 1.4. Is it still neccessary to use a bias tee for an external GPS? https://devzone.nordicsemi.com/f/nordic...
Hello, I am still learning about BLE devices and have a quick question regarding the Generic Access Profile. I understand that GAP defines 2 things:
The discoverability...
Per the notes on https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/Download#supl-c - "Highlight: Updated library made to work with the new modem library...
nRF52832 SDK 17.2
We are trying to get the packet loss/error information on a per channel basis. It is similar to what is being discussed in https://devzone.nordicsemi.com...
I am using NRF dongle in window PC and scanning tags with nRF connect->Bluetooth Low Energy . Is there any way to change the scanning parameters of nRF connect for windows...
Hi,
I have downloaded the nrf5 Sdk 17.02 from the website. And I have found the ble_gls example in ble peripheral example part.
Kit : nrf52832
1. Can you please explain...
Hi,
I am using SDK 17.0.2. I am using write and notification characteristics. There is a write and notification communication between iOS app and device. After successful...
I'm running into a problem where my softdevice is triggering the fault handler but only when I'm also using the USBD. The panic info is below, I've tried to double and triple...
I am working with signled door sesnor and it supports ZigBee 3.0 as it has an install code and mac address on the side of the sensor in the form of a QR code. When I run the...
We are using the latest pc-ble-driver with SoftDevice v6.1.1 and latest connectivity firmware on an nrf52832 (s132) which is connected via usb-uart.
We were previously using...
