void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi
New to using EGU, trying to use it to implement software interrupts. How do I capture an Event?
I can see how to trigger and clear an event using -
nrf_egu_task_trigger...
In the function ble_init, I am getting an undefined reference to sd_softdevice_enable during the linking process. I see that in nrf_sdm.h there is SVCALL(SD_SOFTDEVICE_ENABLE...
Hello,
I am looking for the cost effective simultaneous central+peripheral solution using nrf BLE.
The nrf52810 seems to be hardware capable of doing this but I am...
Hi, I am creating custom ble service.there i need to perform
1. character - READ , NOTIF
2. character - WRITE READ
3 . character - READ,WRITE, NOTIF
I achieved ...
Hi
I'm on a custom board with NCS 1.2.0 and modem firmware 1.2.0.
We have implemented agps, and testing with 2 units with agps colocated with 1 unit without agps. All...
Strange device crash on deprovisioning.
This is probably something incredibly stupid, but I have been fighting this problem for a week and don't know where to turn.
I...
Hello
I program the example code peripheral " ble_app_hrs -pca10040e -s112" on nRF52810 and central " ble_app_hrs_c-pca10040 -s132" on nRF52832 .
I used nRF Toolbox on...
Hi,
we are working with Nrf52 and do not need/use Bluetooth, i.e. our devices will not have the Softdevice stack installed.
I was informed that for the radio certification...
Hello, I am using nRF52840, SDK 16, SoftDevice s140 with SES. I want to configure my device first in connectable mode and then in non-connectable beacon mode. sys_advertising_init...
Hi,
The situation is very simple; I try to use the CoAP Utils library to simplify CoAP usage in an application running on the nRF9160 DK ( https://developer.nordicsemi...
Hello,
I’m using the ble_app_multirole_lesc application from SDK 16.0.0_98a08e2 as is (not modified) on 2 PCA10040 dev kits but unfortunetly both boards return a disconnection...
hi, nordic support
SDK version is 15.3.0
the example is ble_app_uart_c
I have modified the project based on this address： https://infocenter.nordicsemi.com/index.jsp...
Using nRF Connect SDK v2.1.0 and the nRF5340 PDK, are any of the ble mesh samples in the fw-nrfconnect-nrf repo working yet? I've tried both the mesh light and light_switch...
Hi community !
I wanted to know if it's possible to program a board as a client and as a server at the same time ?
Cause i want this card to send data into the network...
