Hi folks,
I'm having some UART trouble - help would be much appreciated, and thank you in advance.
------------------------
Overview:
I'm working on a project that...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Sorry if this is too off topic, I actually don't have any problem with my nrf52840 dongle, but the App I'm communicating with. But maybe someone of you has run into the same...
Hi all,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using an "app_timer" in repeated mode with 10Hz frequency...
I have recently acquired a NAND chip from Micron and would like to use it for storage.
However, looking through the datasheet I found out that the addressing scheme require...
I'm planning using nRF52810 for a new product to reduce the power consumption.
But i worried whether old smartphone with Bluetooth4.0, like Iphone5s can connect with equipment...
I am dealing with the nRF24L01 to develop a remote controller. When I read the specification, I found a specification item, called C/ICO, with a typical value of 12dB in the...
hello,
I'm trying to send long (73B) data on a given characteristic using Android client as the central.
I well received:
USER_MEM_REQUEST OK
> #define...
Hi to everyone!
I'm following this guide to learn how to use secure DFU on a nRF52832DK board.
All steps have been done successfully, or I think so, until I reach the...
I want to find the agent of China, please, thanks
About Bluetooth and 2.4G, nRF52840/nRF52832/nRF52810
(The agent can provide some technical support and sales)
Can someone please explain the below line mentioned in NRF5 Serial port abstraction layer documentation.
Do not use synchronous API (timeout_ms
parameter > 0) in IRQ...
Hi there,
I want to flash nrf51 firmware from another MCU which is connected to nrf51 with UART interface.
I have seen dual bank serial bootloader examples, in that firmware...
Hi,
I know this has been touched on in other posts but I can't find a definitive answer.
I am making a product that sends data from a handheld joystick to a base station...
Hi All!
we are trying to tune Antenna use DTM over UART from examples.
It is works fine for AAAA IC but doesnot for AABB IC.
Why, what's possible problem?
thx...
Hi everyone,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
I need to develop a repetitive task with 10 Hz frequency...
Hi
I am trying to use the serial bootloader to upgrade nrf52 application, but I get verification failure.
I am using nrf52832 with SDK 13.0.0 & S132 SoftDevice v4.0...
Hi,
(1) I look for some methods that suggests is application flag to record. but I set this ble_adv_on_disconnect_disabled = false;. How do I check ble state when disconnect...
Hi
I'm trying to write data to flash and access it via declared const variable.
I can't use UICR because we are on NRF51 and this does not allow to change data in UICR...
