We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
Hi,
Does anyone know if there is a way to achieve 12 bit duty cycle resolution at 25 KHz PWM frequency for 5 channels (individual duty cycle for each channel) using the...
I have one of the new Power Profiler Kits, and it works really well (well done!). The only problem is I can't reprogram the dev kit while it is connected to the Power Profiler...
I have tried to build this by double-click on the .xcworkspace file, in the folder obtained from the downloaded .zip (dated Nov 24, 2016), then "Build + Run". I get 203 errors...
I have modified the template's code so ble_advertising_init should setup manufacturer data, once I have this assignment:
advdata.p_manuf_specific_data = &manuf_data;
...
Hi,
I want to use nRF51422 on ant and ble dual mode.
Does nRF51422 can use sd332 and where has example project
or
The nRF51422 just can use Sd310 only so far.
Than...
Hello,
When line 10 of the below code is executed the system enters the BusFault_Handler, at this point the NVMC register is as followed: Ready = 0x00000001, Config = 0x00000001...
Hello ! I am using Red Bear Nano which has nrf51822 and I have connected it to a computer with linux. On the computer I downloaded arm-gcc version 4_9 and I linked it to the...
hi all!
if I restarting advertising with BLE_GAP_ADV_TYPE_ADV_NONCONN_IND during CONNECTION occur sd_ble_gap_adv_start(..) returns error = 0x07 ( NRF_ERROR_INVALID_PARAM...
Hi,
Would I be able to get more information on the statement below from the nrf52832 datasheet?
"A step increase in supply voltage of 300 mV or more, with rise time of...
As an example, let's see this function from app_hrm (heart rate monitor):
static void conn_params_init(void)
{
uint32_t err_code;
ble_conn_params_init_t cp_init;
...
I am laying out a board in altium using the nRF51422 - just cutting out the essential pieces in the silk box from the nRF51 DK altium project.
I have some concerns. Once...
Hello, I am going to make a PCB to mount the module and programming pins SWCLK/SWDIO/VCC/GND. I wanted to run my module at 1.8v, but I am worried if the nRF51 dev board, when...
[87] CPU: Unexpected wake from System ON Idle when using FPU
This anomaly applies to IC Rev. Rev 1, build codes QFAA-B00, QFAB-B00, CIAA-B00.
I have the PCA10040....
I made a custom board with the nRF52+SDK11.0.0+s132. The firmware is based on the ble_hrs example (modified to fit my board and modified the application, but the basic premise...
