Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi,
We have two sensors, both on the same I2C bus, and we use them with softdevice.
First i must say that the SDK is really poorly written, time wasting and awkward to...
Hi,
is there an example of how to build up a custom USB device? The throughput of the CDC example is only 200 kB/s and we would need a bit more.
Thanks in advance,
...
Hello,
we've got a quite unpredictable issue with a hardfault call : actually this is in this function call : app_error_fault_handler (in app_error_weak.c file)
We use...
I am using the zephyr rtos which run on the nrf52832.
Describe the bug We are using a nrf52832 based board. There are some I2C devices like tsm12 and eeprom. The power consumption...
I'm getting a strange assert from S140 7.2.0 nRF5_SDK_17.0.2_d674dde on a nRF52840 at PC 0x15074.
Frustratingly, it happens a minute or so after boot, but doesn't occur...
Hello Nordic
Im having issues getting logs out of the MSC storage example on SDK16.
When connecting nRF USB connector on the PCA10056 connector to my Windows 10 computer...
Hello,
We use the nRF52832 with SD 17.2.0, Bluetooth LE.
We observe an error when doing the following sequence:
- Build a bonded connection using the nRF Connect...
Hi,
When using the TWI manager you normally provide a callback function that is executed once the transaction has been completed. I'm using the NRF logger module to display...
Hi, Nordicsemi
At present, although SPI uses easy DMA when reading and sending data, in the actual use scenario, I still use gpiote to detect the interrupt pin of the sensor...
I am using the sdk-zephyr. After configing the ubuntu enviroment, i use the west build commond to build the sample project.
But there are errors like these:
[0/1] Re-running...
Hello,
I have few questions about PPI.
----------
1. How to configure PPI channels that runs one after the other? If yes, is there any example?
Because I have two...
I'm having trouble getting the Secure Entry gateway functions to work out of RAM. The nRF9160 datasheet has RAMNSC configurations, so it should be possible. We're able to...
Hello,
I'm not able to locate the QDID for S113 v7.2.0, associated with nRF52832 and SDK 17.0.2.
The product page for S113 indicates that S113 is Bluetooth 5.1 qualified...
Hello,
two part question;
-when a device is registered with the FCC, there is a good amount of documentation uploaded to the FCC website like test reports, photos of the...
Hi I'm wondering if anyone has any tips on implementing a I2C recovery sequence with NRFX 2.3.0 (as included with Zephyr 2.4.99). I've seen this discussed https://devzone...
