void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
We have been using nRF52840 in QFN package in a BLE application. Due to size considerations, we want to upgrade to the WLCSP. I saw that the tuning network is different...
Hi,
We are using nRF52840 DK with 15.3 SDK (latest).
Registered at thisant and got the s340 softdevice for nRF52840 DK.
Please answer are my questions
Where...
In the Mesh SDK the scanner.c file has a power set to 0dBm:
void scanner_init(bearer_event_flag_callback_t packet_process_cb) { memset(&m_scanner, 0, sizeof(m_scanner));...
Hello,
I have nRF52832 and a smart phone with android 7.0.
I want to make a direct BLE connection between nRF and the smart phone, where nRF is a Central device (initiating...
I try to print with serial. How can I print something without a format. I want to print it directly. If yes, which function should I call?
For example, What I am looking...
I have included the reference design for the nRF52840 in my project. Unfortunately, the VIAs in Pads have a hole diameter of 0.15mm and a diameter of 0.35mm and are also still...
Hi,
I checkout v1.0.0 and try to build the at_client-sample but it fails. I cannot see anything I did wrong. I'm attaching the exact steps to reproduce the behaviour.
...
Hi nordic community
I am trying to send stop command to my device(which is connected to my NRF 52840) from my ble module(NRF 52480) after my android disconnected from the...
Hi Nordic engineer:
When I used examples\multi protocol\ble thread\ble_thread_dyn_mtd_coap_cli, I found that the device could not automatically assign LEADER, Router, and...
Hello and Thank you In Advance for Your Assistance. I have been working several days just to get a UART running for interface to a peripheral.
I am trying to connect a UART...
Hi,
As per the document(nrf91_at_commands_v0.9.1) for GPS SNR testing command "AT%XRFTEST=2,1,0" output is single integer as below .
but i am getting output like below...
We are using nRF52832 in our design. We want to collect sensor information along with time stamp. So I took nRF calendar application and tested the same. It was working fine...
I have developed an application that reads data from an analog sensor and transmits data with UART. This app is based off the SDK v14.x uart example, and SAADC example. While...
