here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
There appears to be a conflict between ble_advertising and broadcasting while connected. If connected, the ble_advertising state machine still gets TIMEOUT messages from the...
I am working on light switch demo of mesh SDK 2.1.
I am using nRF52832 board, SDK 15 for softdevice and segger embedded studio for programming the nRF52832.
I programmed...
Hello everyone,
I want to develop an android app, which is able to control multiple LED Lamps in a Mesh Network.
There is an app for provisioning provided by Nordic. Is...
Hi,
When I call sd_ble_gattc_read , I receive the BLE_GATTC_EVT_READ_RSP event very shortly after -- as expected. Within the event handler (registered with the Soft Device...
Hi,
I am considering using baluns instead of discrete components next to my nRF24LE1 QFN-24 chip since board space is at premium.
In application note AN4111 regarding...
I am new to Nordic and have a simple question. I followed the instructions about setting up manufacturer specific data with BLE_Template example here: https://devzone.nordicsemi...
in the middle of the code the MOSI change from idle low to high and resulting in writing 0xFF while reading over MOSI, resulting in getting wrong data. how can i change it...
Using SDK 15.0
Example project: examples/dfu/secure_bootloader/pca0040_ble/ses
Segger Embedded studio V3.50
File main.c line 52
#include "uECC.h" <------ "No such...
chip：52832
sdk：12.3 ble_app_template
when I measure the sleep current consumption use the nordic PPK
I found there is a 30ua peak in every 20ms，could you please tell...
I have some questions to Bluetooth mesh.
1. If I have a mesh Network is it possible to have a connection to a device over all the nodes? Or does mesh just support brodcast...
Hello!
I am a beginner.
I am trying to communicate with the SD card with SPI using nrf 52832.(BLE Nano v2)
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing...
Hi ,
SDK：15.1.0
example：proprietary_rf \ esb_ptx
Because there is no UART function in the example, I want to add it.
The picture is everything I added, is it missing...
Hi Devzone team,
In our SDK, say SDK15.0, there is a head file called "sdk_config.h". It contains a line which looks like below:
// <o> NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE...
WIth the upgrade to the new SDK, registering the callback handlers has been made more difficult to figure out.
The .sdh_ble_observers, .sdh_soc_observersers sections are...
