I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi,
I am porting a NCI (Nfc Controller Interface) driver to the nRF52. One of the things I am struggling with is that, when reading from the device, the amount of data...
At first i have tried the simple uart code from nRF52 where i could send the AT commands properly and UART communication works fine between nRF52 and GPRS module.
Next...
I use a development board with nrf52832 xxaa, BLE demo from SDK works. But I created own board but with nrf52832 xxab(less ROM and RAM) and changed configuration in IAR project...
Hi,
I want to use hardware ECB encryption and decryption in 52840.I had tested the demo from nRF5_SDK_13.1.0\examples\crypto\nrf_cc310\aes\pca10056 . However,i can't find...
When using the APP_TIMER in SDK14 I am having a problem with the application stopping.
I was using the APP_TIMER to flash LEDs and watch for timeouts in SDK13. when porting...
in the sdk_config.h there are plenty of definitions, where "31" is used as a non-valid PIN value
This is destructive if you want to use p0.31
For example:
If one uses...
Hello. I want to use the same pin on nrf52832 for wake up and system off, however I have some issues, like sometimes it doesn't wake up or it is needed to press button few...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Edit: I'm using the softdevice S110, 8.0.0, Nrf51822 chip, Keil uv5.12
Edit #2: Added more detail and revised certain description.
What's the problem?
My program...
Dear partner,
1) Our custmer want the spec of S140, I cann't find that on the inforcenter. can you give me one?
2) By the way i want to know where is my mypage case...
I want to have every node carry a copy of the sensor data in every other node and pass these around on update.
Should I use ANT FIT or FS? What makes mores sense?
As the...
Hello,
How can I detect how much RAM is still free on the heap during runtime, without a debugger attached, just from within the application?
Cheers
Trax
Hi
Can nRF52840 PDK support UART buad rate 921600/1000000 correctly?
I am testing UART with below example for our product development:
nRF5_SDK_14.2.0_17b948a\examples...
Hello, I have problem during dfu otau over ble connection. I use linux version of the nrfutil - my OS version is Linux-4.9.0-3-amd64-x86_64-with-debian-9.1 In some cases i...
I am trying to enable SPI in spi_config.h but SPI3 is missing for the nRF52840.
I need DCX functionality, and from the OPS for nRF52840 it looks like it is only SPI3 that...
