void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
In Nordic\nrf51822\Board\pca10001\s110\ble_app_hrs project,when I add somting into this project but the now that I add dose not work!!?
//this is buzee_gpiote_init()
static...
Hi,
I am working on proximity solution app and I have to implement link loss and immediate alert service but don't know how implement it as I am a learner in this technology...
Hello
I think my question is pretty simple but I would like to clarify this topic, please:
I have read in other threads in this forum that " bonding should eliminate the...
Hello,
Actually, I am evaluating the nRF51822 using the EK. I have some questions as follows:
1- Is the S120 an enhanced version of the S110, and what is the real difference...
I use P0.2 as a wake-up pin, when the system into a deep sleep, I connected a High Voltage in the P0.2, it can wake up, but if I connected a High Voltage in the P0.2 always...
Hi
I got some questions about the RF part of the ref schematic.
1, why the bias voltage for ANT1 anf ANT2 are not the same since they are differential lines?
2, what...
Hi,
Today I use the app timer to start a simple 8bit ADC conversion each second and send in the irq handler.
Now I am trying to use the sw interrupt to execute some...
Hi
I want a 1K Hz square waveform to drive a peripheral device, but I can not get a continuously square waveform on GPIO 19, pls have a look at the picture I attached,...
Hi All
I am facing one issue using app_timer.c, When I put the PRESCALER value as 327 and started timer as app_timer_start(timer_ID, 100, NULL);, It was giving only 920ms...
Hi,
I ran the Nordic nrftoolbox on Sony Z1 android 4.3. I found that the device name is not showing on the list as attached. Running the Nordic nrftoolbox on Samsung S4...
Hi there,
We are using the nrf8001 and a arduino to read out two sensors.
The two measurements should be at the same time and therefore are coupled to eachother.
Is there...
Hi
I try to program my custom board using J-flash and Flasher ARM ( for production ).
Attached my J-flash configuration.
Connection with device is successful established...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I tried the booloader program on nrfgo mother board and it works as it is.
However, after I followed the same procedure and download to our inhouse board which is...
