Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi! I'm able to update the firmware on the nrf5340 over BLE but the BLE settings seem to get overwritten during the update. The master device cannot automatically reconnect...
Hi, im working in a project with the nRF5340-QKAA and I need VDD as output 1.8V, for this reasoin I supply the uC with 3.6V on VDDH like this image:
this works fine...
I'm working on developing a desktop app, which can communicate with nrf52840-dongle or any Nordic device. I'm using UWP to develop the app. I'm new to App development so i...
Hi,
I'm evaluating the nRF9160-DK with the SOFTSIM feature enabled.
I would like to know if there is a way to tell the softsim to wait for APDU response for more than...
Hi, I have a BLE application where I want to use the device firmware updates (DFU) over Bluetooth. I followed the nRF Connect SDK Intermediate tutorial on how to enable the...
Hello!
I'm using the nRF5340 for a school design project and as such am financially limited to relatively low cost board manufacturers.
It seems that most of these manufacturers...
Greetings,
I'm trying to add an existing folder from a project with its' contents, but it seems that it only adds files that are included in the folders, the other nested...
Hello,
I am currently working with the Nordic nRF9160DK and am using the https_client example from the examples in the nRF Connect via VS Code (on Windows OS), and as far...
Hi,
I have been trying for months now and don't seem to find a way to build a signed app for mcuboot without having to build the whole mcuboot itself.
In the board files...
hi,
I am using nrf9160+NCS v2.6.1. When the CONFIG_SHELL_BACKEND_RTT feature is enabled, the power consumption increases by 80uA. After investigation, I found that the default...
Hi
Built and flashed ncs2.7.0 SLM application at NRF9151 DK. It will log booting log messages and then "Ready" as below.
Before ncs2.7.0, I found SLM application only...
Dear All.
Using, for instance, a peripheral nRF52840 SoC, would it be possible to change in real-time the text string being advertised, among several prerecorded ones, according...
Hi,
I am following the tutorial to implement the serial recovery on nrf52840DK https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-8-bootloaders...
Hello,
Im using SDK 15 ble pheripheral and central uart example on my custom nrf52832 board.
I would like to know how to set MIN_CONN_INTERVAL and MAX_CONN_INTERVAL for...
