I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi, we are designing a factory acceptance test (FAT) jig for a custom board containing an NRF9160 SiP. We are testing more than one thousand boards, and probably more than...
Hello
We are using a slave processor with AT command to communicate with the nRF9161 . This is working without problem
But we are initially using the Quick Start 0.2.7...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
We have two cases where the modem has downgraded itself from version1.3.2 to 1.3.1.
1. In the first case, due to water ingress, it appears that the reset pin has been toggled...
System: Windows 10, Vscode + Nrfconnect
I saw a previous post on same topic which fixes the issue by changing the settings in extension like said here ( changing extension...
We have pre-production product (based similar to the NRF9160dk setup with a NRF9160 (LTE-M, GPS) and a bridged NRF52840 (BLE). We are working through certifications for CSA...
Hi all,
I am aware of the different access port protection mechanisms (listed in my previous ticket here: Link ). I did also test both revisions successfully:
For...
Hi.
In our private network we experience one problem.
We can ping Google (8.8.8.8) via APN customer4. In Wireshark traces it is seen that ping is initiated.
On RRC level...
In our current development we are using NRF52840DK and the external memory MX 25R6435F. We are using Settings API to store some configurations on the external memory partition...
Hi, I have the structure for a Vesper VM3011 MEMS microphone:
In the 'overlay' file, I define it as hardware:
When I retrieve the properties from the '.c' file...
We are currently working on a project that has these requirements:
BLE Audio (Broadcast)
BLE Central and Peripheral
WIFI 5/6 (5gHz and 2.4gHz)
BT classic would be...
Hi,
I am currently developing a long range bluetooth module with the U-Blox NINA-B31 BLE module, based off the Nordic nRF52840 chip. I have come across an issue which I...
So, I have built prototype boards using nrf9160, flashed, they are working fine, now need to add to nrf Cloud and realized there are few ways to do that, all are not well...
Greetings
I am going through the BLE fundamentals course and I am doing exercise 1 of lesson 4, creating a custom service. From this exercise, creating the "LBS" service...
Hello,
For context, I am using an EVK-ANNA-B112 development board which has an nRF52832 inside. The development board has an external 32.768KHz HW clock connected to the...
