Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi, we are using NPM1300 with a ICP401835TPRT renata battery. It has a 10k B=3380 NTC (part number NCP15XH103F03RC ). I'm getting a really high temperature reads and very...
Hi,
I am trying to optimize a time critical device for lowest possible latency data transmission over BLE on nRF5340 working as peripheral. Currently my algorithms are implemented...
I'm adding MCUboot to my application and we'll be using our own app to upload new firmware over BLE to the device over our custom comms protocol. I can use the DFU Target...
Working on a nrf5340 project, and running into limits of the size of the flash to store my application image along with mcuboot bootloader.
I had a mucboot setup that fitted...
I have a modified asset_tracker_v2 running with SDK 2.5.0. It is connecting to AWS and sending data perfectly. It has been running for several years without a problem. I am...
Hello,
I’m running the AWS IoT sample on nRF9160DK v1.1.3 using nrf-sdk and toolchain v2.9.0, modem v1.3.7.
Everything works fine when following the instructions with...
Hello community, I am currently looking for a solution outside the 2.4 GHz band and I came across NR+. Does it suit my needs for M2M (Machine to Machine) communication? If...
Dear Nordic experts,
My question is simple, how to get the 6 octets default MAC address by app SW in nRF52840. The question was already raised by someone some years ago...
I have an issue when trying to install nRF Connect SDK on my work computer. I have installed VScode, the toolchain and the nRF Connect extension. The next step would be to...
I have been trying without success to install either the v2.7.0 or v2.8.0 SDK onto my Windows 10 System. Every time/method I've used results in an error equivalent to
...
Hi,
SDK17, Softdevice S112, NRF52805 custom board.
I have baremetal bsp implemented but I am new to Softdevice and struggling a bit with an interface concept beween two...
Hey,
I'm using the nRF5340 and want to run the PTS test with the following configuration: The CAP initiator establishes two audio streams within a single connection to the...
Hello,
We are currently experiencing some unusual behaviour on our feather board (circuit dojo, nRF9160 chip) which we are seeking advice on.
Whats happening:
Device...
Hello,
I'm using NRFX PWM directly because I need something more custom than zephyr's PWM driver provides. I'm trying to understand what .pin_polarity field in the config...
Hello,
When I follow the steps to create a new standalone workspace application for SDK and Toolchain 2.9.0, and then add a new build configuration and build the project...
