Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to send larger UDP packets from nRF9160 (Thingy:91) using Serial LTE modem app.
I am not able to send more than 288 bytes of binary data.
How to send larger binary...
Hello, first, a little background info:
devzone.nordicsemi.com/.../
I want to know if I have successfully set the CCCD handle or not with my Android program.
And...
I've seen the Connectivity Bridge Application in the ncs, however I can't find any sample application for the nRF91 side showing how it can send/receive data and events from...
Hello
I have a cheap ST-link that I use heavylly to program STM arm cortex chip.
So my guess is that it should work for this case.
I am following this tutorial:
...
Hello.
When I try to import a project , it will show a error. I can't build it . Pleave view following info and help me about it . Thank you.
Harrison
BR!~
Hello,
I try to add the BLE-Template code into my existing program code, but I get the following linkage error. I have defined the following flash_placement.xml for my Segger...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
Hi,
Add BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event handle at ble_lbs service in example of ble_app_blinky. but when client read the characteristics 1524 or 1525, no BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
Environment: Windows 10 nRF Connect SDK 1.4.0 I followed all of the steps described in nRF connect SDK documentation and tried to build "Blinky" sample from zephyr as shown...
use s132 on NRF52832
when i used sd_ble_gap_connnect () to connected peripheral device,it return NRF_ERROR_INVALID_ADDR
the addr copyed in scan_evt_handler() by NRF_BLE_SCAN_EVT_FILTER_MATCH...
Hi ,
I have made basic binary sensor based on light bulb project,
wanted to add default BIND-TO-Gateway ( Short address 0x000). Gateway is CLI_AGENT .
I am try to add...
select at_client folder
west build -b nrf9160dk_nrf9160ns -p
shows this warning
```
warning: The choice symbol LTE_NETWORK_MODE_NBIOT (defined at /Users/paul_tanner...
Hello, we are using a usb dongle where we have a NRF52840 and RFX2401 PA+LNA frontend. The latter can be controlled with TX_EN and RX_EN pins. Please see attached schematic...
Hi there,
I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. Everything except one single thing is working. I've just implemented FDS...
