I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi guys.
I was porting the project from nRF52832 to nRF52810 when I get the following message:
"When using s112, NRF_SDH_BLE_CENTRAL_LINK_COUNT must be 0."
After searching...
This is in continuation to the previous question I asked which is linked here: https://devzone.nordicsemi.com/f/nordic-q-a/52575/making-a-ble-ibeacon-with-gap-gatt-profiles...
Hello,
I have used for my application the reference design of NRF52832.
The connector MURATA MM8130-2600 is used to have the choice between the PCB antenna and an external...
I have refer to this topic for setup multilink with NUS. https://devzone.nordicsemi.com/f/nordic-q-a/18804/mismatch-between-connection-handles-in-ble_nus
But, i met a wrong...
Hi Nordic,
While testing USB CDC example with nRF 15.3.0 in PDK board, I see USB is not recognized. I have gone through the same issue posted in Forum. Is it the issue with...
I have a question about “BLE_HCI_CONN_INTERVAL_UNACCEPTABLE”.
SDK: 15.3.0 Example: ble_app_multirole_lesc (source changed from sample) Device: EYSHJNZWZ (nRF52832)
The...
This microcontroller is advertised as mbed enabled. Does that mean that it can be easily programmed using mbed api in an mbed environment. I want to work in a c++ environment...
I am trying to use the nRF52-Development kit with (N52832) and using nRF5_SDK_15.0.0. What my application is to broadcast an iBeacon Packet (with Major, Minor, RSSI and UUID...
Hi,
I followed this tutorial ( https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/merging-two-ble-examples-together ) of combining UART example with other...
Hello. I use nrf52832 on Adafruit Feather board among with nrf5 SDK. As a default I can log any info via NRF_LOG_DEBUG to my serial monitor. But how can I use Serial input...
I was wondering if the standalone nRF51822 microcontroller has support for i2c. If so which pins are supported. There doesn't seem to be any reference on i2c for the board...
Hi,
I bought a custom nrf52840 board and I need to program my firmware on this SOC with PCA10056 DK debug output port. in below you can see part of shematic of my custom...
I have some custom models in my mesh application in addition to SIG standard models. As can be seen with interactive_pyaci script when i read the composition data of my device...
Hi guys.
I'm working with a nRF52832 custom board.
In my case my board communicates with the LIS3DH through i2c protocol. In the other hand based on LIS3DH datasheet the...
