Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
HI,
I purchased the nRF51822 Bluetooth Smart Beacon Kit ( I knew it's discontinued ) to perform a quick and simple POC (put my custom 31 bytes for the beacon to advertise...
Hi All.
I have an issue with my development kit. I was working with DFU so I flashed the secure_bootloader project in my nrf52 DK so it is working fine.
But after this...
Hello,
I have an Adafruit Feather M0 Bluefruit LE with an nRF51822 chipset from Nordic and I am currently dealing with Bluetooth Low Energy, especially with profiles, services...
Hi,
As I am new to this BLE applications I am unable to get actual flow of implementing a service to send application specific alert notifications from server which includes...
Hi,
I´m trying to combine the examples "BLE_app_uart" with "TWI_Sensor", because I would like to read data from sensor and put them to my BLE characteristics. I´ve done...
Hi sir
I am getting the current date and time from GPS module . I want to calculate the number of second between 1 Jan 2000 and current date and time. but i am getting how...
Hello, Everyone.
I'm developing a beacon to check the battery level.
I'm current using
nRF51822
SDK11.0.0
Softedevice S130
My inquiry is nRF52 series is...
We just received a batch of custom boards containing the nRF9160. I would like to test them and start developing our actual application.
So far I have switched SW11 to match...
Hi everyone.
I'm using pc_ble_driver_py with nRF52840 USB dongle with burned connectivity_4.1.1_usb_with_s140_6.1.1.hex.
pc_ble_driver_py is modified by me to support...
Hi,
Is there anything to match the above subject with SPI ?
The coding for sending and receiving should be written on the both sides of sensor driver and master side?...
Hi,
I am looking for documentation about the reflow process of the nRF9160, but I cannot find it on the documentation webpage. Is this information available at Nordic? I...
Hello.
When Notifying about 100 bytes of data, sd_ble_gatts_hvx() is sent 5 times. Occasionally NRF_ERROR_RESOUCES occurs. Currently MTU_SIZE is 23, and the actual data...
based on the comments in sdk_config.h, the softdevice uses priorities 0, 1, 4, 5. yet in app_util_platform.h, the macro _PRIO_APP_LOW_MID is given the value of 5. is this...
Hello
I need to do pairing with Android devices without passkey in ble_app_uart example.（ Device nRF52832 ,SDKv16.00, softdevice S132 )
I use ble_app_gls example and Android...
Hi
I am using ble_app_blinky but led is not blinking. I am using P0.27, P0,28, P0.29 pin for LED but in program pin of LED are define as
#define BSP_BOARD_BUTTON_0 0 ...
