Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi, I am developing 3 devices, two of these devices should act as nodes and send data from their respective IMU sensors to the 3rd device(central device).
I have been looking...
Hi all,
My name is Szabolcs Vass. We are developing a project with nRF9160 SiP on our custom board. We want to send some measurements periodically to an MQTT server. After...
I have realized the cutdown function with the examples. But now I want to reflesh the number I have published, which means that I first publish a number, then I want to publish...
Hi,
We are using nrf51422 in our project and SDK we are using is 12.3 and soft device is S130. In our project we need Bluetooth device should be connected to upto 3 devices...
Hi
I did DFU with button, i can enter and load zip pack over nrfToolbox mobile.
I tried butonlessDFU, i copied services "experimental_ble_app_buttonless_dfu" and with...
Hi,
I am evaluating the ble_app_template example with nRF52840 SDK.
I added code to create custom service and custom characteristics in the following link:
https://github...
Hi,
i have to watch my program flow in segger debugging mode, so that i enable
#ifndef NRF_LOG_ENABLED #define NRF_LOG_ENABLED 1 #endif
in sdk_config.h file.
now i...
Hi,
I want to display an image sent over Bluetooth on my screen which uses the driver st7735. So I have an application which can send images, and I receive data in the function...
Hello,
we have a problem on BT certification with nRF52810 chip. Certification lab replied that TCRL-2018-2 which is mandatory.
Does anyone know where I can get the QDID...
Hi,
I just wonder when hvn_tx_queue (the notification queue) in softdevice is emptied? Is it emptied on disconnection if it still has notifications in queue to send?
Hello.
I have nRF51822 and nRF52832 boards.
I can use both to capture BLE frames with Wireshark on Linux, and I test that with RACCOON also to capture traffic in terminal...
I'm using the DFU module from SDK 9.0 - I enter the DFU by writing to the DFU control point. Is there a way to exit the DFU and have it go back to the app?
Have seen many good thread explaining this model. But didn't find any full example code for it for client and server Model.
I have tried light switch demo and working fine...
Hello!
So I have a new nRF52811 board which was designed by someone else, that I need to develop some pretty simple firmware for. Full disclosure, the design is based on...
Hi I am working on nRF 52832 and nrf 52840 dongle. I want UART service to be used in my application and application should allow me to scan peripheral devices with user command...
