Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi, Nordic
I need write some information to flash, then power off and power on, nRF52 still can read previous information. But now, nRF52 can not read, maybe ESB is still...
Hi,
I'm having issues with my MPU6050 sensor. I'm trying to get yaw, pitch and roll raw sensor values from MPU6050 sensor using DMP on MBED platform but without success...
I have just read nRF52840 Engineering A Errata v1.0, it looks like nRF52840 is like swiss cheese.
When can we expect some solid version of nRF52840 chip on the market?
Hi DevZone
Does the SWF switch at the PCA10040 automatically switch to the antenna I have put on my connection probe? ( www.digikey.com/.../1775923)
Thanks in advance...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Sir,
I am working in nRF52832 board with pca10036. I want to know whether the board supports a loopback control in SPI mode. I need to try for transmitting and receiving...
Hello,
I'm trying to use NFC module on nrf52382 chip (DK PCA10040) and prepared firmware "nfc_text_record_pca10040" from examples of SDK v13. After flashing the Mifare ultralight...
Hi,
In the nrf52.h, SPIM_RXD_Type is defined as below.
typedef struct {
__IO uint32_t PTR;/*!< Data pointer */
__IO uint32_t MAXCNT;/*!< Maximum number of bytes...
i am working with Nrf52 + Visualgdb complier.
nrf_drv_gpiote.h contains designated initializers which aren't supported by C++. I'm including all SDK headers inside an extern...
Hi,
I would like read a long characteristic.
I know that I have to use sd_ble_gattc_read and I have to multiple call this function.
But I don't know where I have to call...
Hello,
I want to implement some kind of control point. This means, that I want to handle BLE write events to some characteristic. I've seen that the payload of the ATT...
Hi,
i tried to find an example with SPI which describes the connection between two nrf24LE1, one as master and one as slave, but i could not find anything. I need the following...
Trying the ATT_MTU Thourughput Example with SoftDevice:
nRF5_SDK_13.0.0-1.alpha_055eef3/components/softdevice/s140/hex/s140_nrf52840_5.0.0-1.alpha_softdevice.hex
on...
