here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
We have an NRF51822 running S120 at 32MHz.
Our system has two removable batteries. If a battery is removed we need to switch to the other battery as fast as possible. We...
For TWI, SPI and UART is there a significant power savings from powering down the unit when not in use vs just disabling it?
Disabling the unit seems reasonable, but powering...
Hi!
I was trying to use nRFLoader to update firmware using example DFU Bootloader but app hangs on "Discovering" (after selecting device to update). What can be the reason...
Currently I can upload new application firmware smoothly (I use the dual bank setup). However, I have to use packets of size 20, so this takes a long time.
Is there actually...
hai ,
i am using the NRF51822 development kit. The NRF51 dongle i have used as a sniffer and a master control panel. Is it possible to load and run a s130 softdevice and...
Hi, I'm trying to estimate the nRF51422 current when running ANT. Does the softdevice use the RTC (LF oscillator) when in wait mode to save energy? Thanks
The Segger programing interface works. The virtual com port appears on my PC (COM5). The problem is that there is no board listed in the Motherboards section of the Device...
Hello,
currently I try to implement a GATT server on a nrf51422 with the s310 Softdevice. For testing I use the LightBlue IOS client on an ipad. I can see my GATT server...
I am creating an Apps which will give me a list of the running Apps in the background and foreground.
Hence Using XCode, I want to programmatically detect
List of Running...
I have a Arduino board and I want access to Ant Stack by UART. I flashed S210 in my nrf51422.
I try connect the Arduino RX/TX with TX/RX (P0.12 / P0.13), but none. Also...
Hi Nordic,
I'm wondering if I can use IAR Workbench to download SDK for nRF51DK rather than Keil. I want to develop a beacon that uses Bluetooth Smart. Can I do that in...
Hi,
Does the .hex file for V7.1.0 include the master boot record? I'm writing a JLink script to flash it and I'm trying to figure out, once converted to a binary file,...
I have the PCA 10028 Board. I would like to add a characteristic on an already existing service.
In the nAN-36 I see, what is necessary to set up service and characteristic...
Dear Forum,
I just unwrapped my new nRF51 DK board and already played with some mbed example programs which worked beautifully! So first of all - thank you Nordic & mbed...
What capacitors would you recomend for this 16MHz Quartz http://www.jauch.de/ablage/med_00000848_1411137106_JXS32-180914.pdf to ensure 40ppm frequency tolerance for nrf51822...
