Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I am writing to inquire about the MTTF, MTTFd, MTBF and/or FIT value of the nRF52840. nRF52833 and nRF52832. Where can I find these values?
This question has been...
Hi Team,
The customer have used NRF52832-CIAA-R. The datasheet of the Bluetooth module has NFC function. Please help provide the reports of EN 300 330-1 and EN62311 for...
Hello Nordic Forums.
I have been struggling for the past couple of days to try to get the SPI working. I never thought that something this easy could have become such a...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hello,
I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
We are checking the feasibility on LE Audio + Mesh + Bidirectional streams. A picture is attached for the situation. We would like to know how to apply Mesh network on LE...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if all of the power components are required.
The nPM1300 appears to provide...
Hello,
We have a requirement to ensure all private keys are stored within AWS Key Management System (KMS) and the only way to interact with these is via the KMS APIs that...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I recently had a question about AES encryption on the nRF9160 and about how to store 32-byte encryption keys. The ticket was closed after I got the following answer: " we...
Hi,my board is nRF52840,and the demo is periodic_sync_conn within ncs2.7.0,
I want to establish periodic sync with the AP whose rssi is better，but i am failed。The ESL will...
Hello Nordic team,
I am working with the samples/bluetooth/shorter_conn_intervals sample on NCS v3.2.3 using two nRF54L15 DK boards.
I understand the difference between...
Hello, Recently I got an nRF9151-DK and I am following the Cellular IoT Fundamentals course. When it was time to connect the device to nRF Cloud (Lesson 1, Exercise 1), it...
Hi there,
I am developing a Matter light color temperature lamp product based on the NCS v3.1.1, and I need to store some custom user data in NVM (Non-Volatile Memory) within...
