Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to debug firmware on our production device, but after programming the device a couple of times, I am unable to program.
Inside of Segger I see this log:
j...
Hi everyone,
In my company we are working with the last SDK release, and we build projects with make and gcc toolchain.
I have a quite wide request : since I'm using makefiles...
Hi all,
I have a custom nRF52840 board that transmits 32-byte packets to mobile device and I want to achieve maximum transfer speed.
The code is based on the ble_app_uart...
Dear all
The issue is:
heartRate and battery levels set by "bt_gatt_notify" in peripheral hr sample on nRFConnect v1.5.0 are not shown in iphone app of "nRF toolbox" ...
Hi All,
I am using the nRF52840, with SDK140 v15.0. I have configured the nRF52840 to be a SPI slave to a NXP processor. When I connect the logic analyzer I see signals...
Hello,
I am trying to build on the nrf5340_cpuappns sample, however this snippet seems to always warn unable to allocated UART send data buffer. Is there any reason k_malloc...
Hi Everyone!
nrf_serial.c and nrf_serial.h are gone in SDK 17.0.2. There are present in 16.0.0. I do not see any mention of this in the release notes.
Was this module...
i am using example code ble_uart for controlling gpio(led & buzzer) by editing bluetooth data handler. I am driving a buzzer using pwm.
led working fine i.e turned on/off...
In nRF Connect SDK I see drivers for BH1749 sensor from Thingy 91, but not for BH1745 from Thingy 52.
Is it possible that the BH1745 sensor will be supported soon? Looks...
I tryed to use the pynrfprog with a Segger-ARM-Flasher to update modem DFU.
I changed the python skript to follow - because there are 2 Segger-ARM-Flasher installed in...
Hi,
When I connect my device to an external power supply, it restarts randomly. It sometimes happens once every minute, sometimes once every 10 minutes. I couldn't find...
Hello,
I am transmitting 1 byte BLE data across a central and peripheral and the central does other things like control PWM, sample SAADC (scan mode), GPIO pins interrupts...
Hello,
When I am loading my project into SES I get the following warning message.
CMake Warning at C:/Zypher/v1.5.0-rc1/zephyr/CMakeLists.txt:1354 (message):
WARNING...
I have a nRF9160DK board and a want to generate a simple interrupt when I press button 1 (pin 6) on the DK board. When this works I will move to a different GPIO and hook...
I'm developing a small function that split string using delimiter (,) but i can't use strtok (undeclared function error)
so i added (CONFIG_NEWLIB_LIBC=y) to prj.conf file...
