Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi team,
I was comparing the ble_app_hrs example from SDK v15.3.0 to SDK v16.0.0 and noticed a big difference in the average power consumption. The only change I made to...
I am testing the ble_app_blinky example on nRF52840 BLE SoC and the "nRF Blinky" Android application example which uses the Android-BLE library from NordicSemiconductor. My...
The current implementation of Mesh Config using the flash manager lack a memory listener which can cause it to never retry a store or delete operation.
Assume the following...
Dear Sir,
Could you please recomend board(hardware) that I could move my code that was developed using NRf52 SDK.
I am using ANT functionaluty and s212 software
Best...
Hi Nordic,
I had an initial project with a multilink central connecting to several peripherals through a NUS service, the system is working OK but then I added another connection...
I am using PCA10040 development board for flashing.Same it was working fine to flashing the Custom board.
Now suddenly not flashing to the custom board same board which...
I am planning to use CP2102 (USB to UART) and RF-BM-ND06 NRF52840 bluetooth module for sniffing BLE packets .
Or as an alternative for Nordic Bluetooth USB dongle.
But...
Hello, I'm pretty new to Nordic devices but I have already some experience with other ARM based devices though...
I'm playing with Timers bare metal instructions and figured...
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK. I have an SPDT RF swtich which I want to use for switching between two antennas. I want...
Hi,
I've already asked this problem few days ago, but I couldn't figure out the clear answer.
The above figure shows the VDD values of BLE chip. The power supplied...
0> <debug> nrf_sdh_ble: BLE event: 0x26. 0> <error> app: Fatal error
I started with the nrf_tempelate project and used nrf_uart to add uart service. It works fine but after...
Hi,
I want to know that, can we use this nrf91 for transferring the real time data with tab or mobile phone beyond BLE range. I mean, do we analyse the real time data from...
Hi:
I have no dongle or any other Dev board such as PCA10031. Can I use nrf51822 and cp2102 as a usb dongle to work with MCU of PC? If the answer is yes, what should I do...
Hi All,
I am trying to decrypt some data coming in on my board with AES ECB mode. I know that there is no decryption function for ECB and you have to use the same sd_ecb_encrypt...
